GE Druck PV 621 Скачать руководство пользователя страница 6

Страница: 6 / 55

Issue 1

vi Summary of functions

K0457 - [EN] English

Summary of
functions

This table gives a summary of the available functions with the
PV 62x pressure stations.

PV 62x - pressure station functions

Function

Pneumatic pressure stations

PV 621: Pressure from vacuum (95%) to 20 bar (300 psi);

* PV 622: Pressure from vacuum (95%) to 100 bar (1500 psi)

Selector switch to change the pump operation from pressure
generator to vacuum generator

Needle point pressure release valve to control the release of
pressure.

Hydraulic pressure station

* PV 623: Hydraulic pressure from 0 to 1000 bar (15000 psi)

Internal hydraulic reservoir: 100 cm

(6.1 in

)

Self sealing pressure module connection to prevent fluid leaks.

Fast thermal stability for devices attached directly to the pressure
test connection (

≤

one minute)

All pressure stations

“Quick fit” pressure adaptors for the device under test

** Pressure connection for a PM 620 module

Volume adjuster to give accurate control of pressure conditions.

Latch mechanism to attach the DPI 620 calibrator to make a fully
integrated pressure calibrator instrument

** Pressure relief valves (PRV) to give overpressure protection.

** Pressure s DPI 620 cali PM 620 module

Measure pressure/Leak test

Documenting software

HART

(Highway Addressable Remote Transducer)

communications software to set up and calibrate devices that use
the HART

field communications protocol.

* Refer to Chapter 7 (Specification)
** Optional item

PV 622

PV 621

PV 623

Pressure calibrator

Содержание Druck PV 621
























































Результаты поиска

Содержание Druck PV 621

Отзывы:

Похожие инструкции для Druck PV 621

Бренды по названию

Популярные бренды

GE Druck PV 621, Руководство пользователя

Результаты поиска

Содержание Druck PV 621

Отзывы:

Похожие инструкции для Druck PV 621

Бренды по названию

Популярные бренды