GE Dishwasher Скачать руководство пользователя страница 6

6

Installation Preparation–Hot Water Supply

PREPARE HOT WATER SUPPLY

Hot Water Line

• The line may enter from either side, rear, or floor 

within the shaded area shown in Figure F.

• The line may pass through the same hole as the 

electrical cable and drain hose, or cut an additional 
1-1/2" diameter hole to accommodate the water 
line. If a power cord with plug is used, the water line 
must not pass through the power cord hole.

Figure F

Water Line Connection

• Turn off the water supply.
• Install a hand shut-off valve in an accessible 

location. (Optional, but strongly recommended and 
may be required by local codes.)

• The water connection is on the left side of the 

dishwasher. Install the hot water inlet line, using 
3/8" or larger copper tubing. Route the line as 
shown in Figure F and extend forward at least 19" 
from rear wall. 

• Adjust the water heater to deliver water between 

120°F and 150°F.

• Flush water line to clean out debris. Use a bucket 

to catch water and debris.

• The hot water supply line pressure must be  

between 20 and 120 PSI.

5"

5"

6"

679DiaE

Cabinet Face

Shut-off

Valve

2" From Floor

19" From Wall

2"

From

Cabinet

1-1/2" Dia.

Hole

Hot

4"

4"

 

CAUTION

The hot water supply line pressure must be at least 20 PSI. 

Lower pressures could cause the water valve to leak and 

cause water damage.

Sink Utility Connections

Sink faucet hot and cold water lines and the sink 
drain line must run above and adjacent to the 
dishwasher, not behind it. Refer to Areas A and C 
in Figure A on page 3 and Figure F1 below. This is 
necessary to provide clearance for the dishwasher 
when it is installed in the cabinet. Utility lines routed 
directly behind the dishwasher will interfere with 
placement of the dishwasher in the cabinet and 
cause it to extend beyond the adjacent cabinets.

Figure F1 illustrates an installation using a double 
bowl sink, a disposer and a high drain loop. 

Note:

 All utility lines are above, below or adjacent to 

the dishwasher. None are routed behind it.

6” Double-bowl

stainless steel sink

Countertop

25” deep

1-1/2” thick

1-1/2” Close

elbow

Dishwasher

water inlet

valve

Dishwasher

drain hose

Hot water supply

to dishwasher

Valve to shut off

water to dishwasher

Cold water

Hot water

2101 SpaceMaker Install

Spacemaker

®

dishwasher

Figure F1

Содержание Dishwasher

















Отзывы: