READ THOROUGHLY BEFORE INSTALLING
GENERAL
This luminaire is designed for outdoor lighting applications, and should not be used in areas of limited
ventilation, or in high ambient temperature enclosures; it should be installed and maintained according to
following recommendations.
UNPACKING
This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect
to confirm.
INSTALLATION
Reflector Rotation: Reflectors may be rotated such that socket is in any of four positions. This allows for
variations in beam aiming. In order to rotate the reflector the following procedure should be followed.
1.
Rotation is best accomplished before mounting the luminaire on pole.
2.
Note the rear edge of reflector position with respect to hinges (edge inserted into hinge pocket). Access
reflector by loosening reflector plate to main housing screw and allowing reflector plate assembly to lie on
door assembly. It is not necessary to detach tether.
3.
Remove four screws which attach reflector to reflector plate.
4.
Rotate reflector to desired position, being careful not to twist socket lead wires.
5.
Reattach reflector by reinserting four screws.
6.
Reposition reflector plate by inserting rear edge of plate into hinge pocket and attach plate to main housing
with screw.
MOUNTING
CAUTION
Unit will fall if not installed properly
•
Follow installation instructions
WARNING
Risk of electric shock
•
Turn power off before servicing
–
see instructions
CAUTION
Risk of burn
•
Allow lamp/fixture to cool before handling
NOTE:
Power leads should be pulled as mounting parts are assembled, verifying that leads are free and not
pinched. Ballast voltage selection is best accomplished before mounting luminaire. See
Wiring
for instruc-
tion.
A. ARCHITECTURAL MOUNTING: (Arm)
1.
Install nut plate inside pre-drilled pole with nuts to inside. Secure with screw provided.
2.
Install the two (2) studs insuring that they fully penetrate the nuts on the nut plate.
3.
Align the upper and lower guides on the inside of the mounting arm with their respective studs and slide it
into place against the pole.
4.
Open luminaire door by pushing inward on latches while supporting door. Release reflector plate by loosening
plate main housing screw and allow plate to hang from tether.
5.
Install the luminaire and secure with flat washers and locknuts provided. Align the system as the nuts are
tightened.
CAUTION: Ensure that nuts fully engage the two studs. Correct tightening of stud nuts
is important to ensure proper function of mounting system. Torque to 18 - 22 foot pounds.
B. OTHER MOUNTINGS
External Slipfitters, Knuckle Flat Surface, Knuckle Pole Top and Round Pole Adapters are
also available for use with housings machined with a diagonal hole pattern. Installation is similar
to the Architectural Mounting.
CAUTION: Do not mount any unit below or greater than 60° above horizontal.
LAMP INSTALLATION
Use only lamps specified on nameplate. Observe lamp manufacturer’s recommendations and
restrictions on lamp operation, particularly ballast type, burning position, etc.
LAMP TIGHTNESS —
The lamp should be securely inserted to NEMA-EEI specified torque of 35 inch-pounds,
which is best achieved by very firmly tightening to insure application of sufficient torque. Tightening must be
sufficient to fully depress and load center contact of socket.
WIRING:
Make all electrical connections in accordance with the National Electrical Code and any applicable local code
requirements.
GEH-5823A
INSTRUCTIONS
Decashield
®
1000 DSA (Arm)
Verify that supply voltage is correct by comparing it to nameplate.
If unit is designated as multivolt or multiwatt, follow specific instruction.
Do not remove insulated connectors from wires not needed for required voltage connection.
Connect supply leads to internal terminal board as shown on wiring tag.
NOTE:
Terminal board will accept supply leads ranging in size from AWG No. 14 through No. 6 (check
nameplate for minimum temperature requirement and electrical data).
IF SINGLE VOLTAGE:
All single voltage ballasts are pre-wired such that user need only connect the supply conductors.
IF MULTIVOLT:
(120/208/240/277 volts)
Connect the ballast lead with the insulated terminal to the desired voltage terminal as indicated on the
ballast terminal nameplate.
IF MULTIWATT:
Multiwatt ballasts are available in various combinations of wattage. See wiring instructions on wiring tag
inside the luminaire. Reattach reflector plate, close door and check for secure latch engagement.
Installation is complete.
PHOTOELECTRIC CONTROL (if option present)
Photoelectric control receptacle should be oriented before control is installed. Loosen the two holding
screws and rotate receptacle until “North’ is directed as near as possible to true North. Tighten holding screws
and install control.
MAINTENANCE AND CLEANING
It will occasionally be necessary to clean outside of door glass to maintain light levels. Frequency of cleaning
will depend on ambient dirt levels and minimum light level which is acceptable to user. Door glass should be
washed in a solution of warm water and any mild, nonabrasive household detergent, rinsed with clean water and
wiped dry. Should the optical assembly become dirty on inside, wipe reflector and clean door glass in above
manner, and replace any damaged gasket.
The light output of a luminaire is also dependent on age of lamp. In applications where light levels are critical
it may be desirable to replace lamps before they burn out. Lamp manufacturer can provide data showing how lamp
light output decreases with use.
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or maintenance.
Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be referred to GE Lighting Solutions.
g
GE
Lighting Solutions
