GE CARESCAPE Monitor B850 Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 192

background image

Maintenance and checkout

125

2106778-001

10 Maintenance and checkout

This chapter specifies the checkout procedure and the maintenance activities to be performed
to the patient monitor after corrective maintenance and during planned maintenance.

WARNING

Only perform maintenance procedures specifically described in the manual.

WARNING

Planned maintenance should be carried out at recommended interval.

Failure to implement the recommended maintenance schedule may cause
equipment failure and possible health hazards.

NOTE: The manufacturer does not, in any manner, assume the responsibility for performing the
recommended maintenance schedule, unless an Equipment Maintenance Agreement exists.
The sole responsibility rests with the individuals, hospitals, or institutions utilizing the device.
NOTE: Refer to Module Frames and Modules Service Manual for corrective and planned
maintenance checkout procedures of the parameter modules.
NOTE: Refer to the PDM section in the Module Frames and Modules Service Manual for the
battery maintenance procedure of the PDM battery.

Corrective maintenance

Service personnel shall perform the following checkout procedure steps after any corrective
maintenance, before taking the monitor back into clinical use:

Performed service activity

Required checkout procedure

Visual
inspections
(section 10.1)

Electrical
safety test
(section 10.2)

Functional check
(section 10.3)

After detaching or replacing:
- Power supply
- CPU PCB assembly
- Lithium -ion battery (timekeeper)

Yes

Yes

- All steps

After detaching or replacing:
- 3rd video card

Yes

Yes

- 10.3.1 Start-up
- 10.3.2 Display
- 10.3.3 PSM / PDM

After detaching or replacing:
- Enclosure Kit
- Hardware kit (or any part of this)
- Speaker assembly

Yes

Yes

- 10.3.1 Start-up

After detaching or replacing:
- Label kit

Yes

No

- 10.3.1 Start-up

After detaching or replacing:
- uDOM

Yes

Yes

- All steps

After detaching or replacing:
- M-Port keypad Kit
- Remote Control Kit

Yes

No

-

10.3.1 Start-up

-

10.3.5 Keypad and remote

«
...
131
132
133
134
135
...
»

Содержание CARESCAPE Monitor B850

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B850

Бренд: Daavlin Страницы: 13

Бренд: Daavlin Страницы: 27

Бренд: B&K Страницы: 5

Бренд: B&K Страницы: 28

Бренд: Canta Страницы: 2

Бренд: vanEE Страницы: 52

Бренд: Caddon Hives Страницы: 3

Бренд: jablotron Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: T&D Страницы: 28

Бренд: uniprox Страницы: 3

ZA top SM315.100A

Бренд: ZIEHL-ABEGG Страницы: 76

ABS-Lock III-BE

Бренд: ABS Страницы: 8

Aristo WeldCloud Mig U5000i

Бренд: ESAB Страницы: 28

Aesculap S4 Cervical

Бренд: B. Braun Страницы: 43

Dynamique Biski

Бренд: Enabling Technologies Страницы: 44

Бренд: Becker-Elektronik Страницы: 24

Add-It AFI 5016-H

Бренд: DIG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды