manualshive.com logo in svg

GE BiliSoft, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
GE BiliSoft Скачать руководство пользователя страница 31

Chapter 6 

Troubleshooting 

Alarm/Troubleshooting Guide 

Symptom 

Likely causes 

Troubleshooting steps 

Unit Overheated 
Indicator light is 
on. 
 

 

Clogged air filter, 
blocked vents, 
fan failure. 

1.  Turn off the standby switch and 

disconnect the power cord from the 
outlet. 

Note

: It can take up to 10 minutes for the 

thermal cutout switch to reset and allow the 
unit to be used again. 
2.  Make sure that the air filter in the back of 

the unit and the air vents on either side 
of the unit are unobstructed.  If the air 
filter needs to be removed, take the unit 
out of service and seek assistance from 
service personnel. 

3.  Plug the power cord into an outlet.  Make 

sure a fiberoptic light pad is attached.  
Turn the standby switch on. 

4.  Verify that the fan is on and allow the 

unit to run with the fiberoptic light pad 
attached. 

5.  If the fan is not running while the unit is 

turned on or if the Unit Overheated 
indicator light turns on again, remove the 
unit from service and seek assistance 
from service personnel. 

LED failure 
indicator light is 
blinking. 

 

At least one of 
the three LED 
pairs is not 
operating. 

1.  LED module needs to be replaced by 

service personnel. 

Note:

 The system may still be used until the 

LED module is replaced.  However the 
intensity will be lower than the specification. 

M1110147 Rev. 

5

 © 2007 Datex-Ohmeda. All rights reserved. 

6-1

 

Содержание BiliSoft

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды