background image

ASTAT 

®

-IBP Plus Service Instructions

Prices and data subject to change without notice.

3

Power Supply Board Replacement

The Power Supply Board is located as shown in Figure 5.

It contains gray and orange transformers visible from the

sides.

1.

Remove the following components:

a.

The cover, as described in steps 1–2 of 

Cover

Removal and Replacement

.

b.

The Logic Board, as described in steps 2–3 of

Logic Board Replacement

.

2.

Remove the four screws holding the Power Supply

Board to the black plastic housing, as shown in

Figure 6.

3.

If a yellow-green wire is connected to the bottom of

the Power Supply Board, it must be disconnected.

Lower the top of the Power Supply Board to view the

red and white gate leads to the SCRs, as shown in

Figure 7.

NOTE:

 Check the red and white gate wires for a marked

number before removing these wires. Each gate wire

must have a number corresponding to the terminal

numbers (1–12) on the Power Supply Board to facilitate

reassembly.

NOTE:

 Vérifier les chiffres sur les fils de porte avant

d’enlever ceux-ci. Chaque fil de porte doit avoir un

chiffre correspondant aux chiffres de la borne (1–12)

sur la plaque de la boîte d’alimentation pour faciliter le

réassemblage.

4.

With a small screwdriver, remove the red and white

gate wires from the small four-point gate Terminal

Boards, one on the component side and two on the

solder side of the Power Supply Board.
These wires must be reconnected to the new Power

Supply Board at the proper number terminals for

proper operation of the starter.

5.

Lift off the Power Supply Board. Remove and save

the hex stand-offs, nuts, and washers from the Power

Supply Board for use on the replacement board.

6.

Attach the stand-offs to the new Power Supply Board.

Place the new Board in position in the ASTAT-IBP.

Figure 5. Location of the Power Supply Board.

Figure 6. Removing the screws holding the Power Supply Board

to the housing.

Figure 7. Gate leads, Power Supply Board, and Protection Board.

Gate Leads

Protection Board

Bottom of Power

Supply Board

Gate Terminal

Board

Screw

Power Supply Board

Ribbon Cable

Содержание ASTAT-IBP Plus



















Отзывы: