GE AKTAprime plus Скачать руководство пользователя страница 31

Страница: 31 / 68

Installation

ÄKTAprime plus is delivered in protective packing material and shall be unpacked with
great care.

Any equipment connected to ÄKTAprime plus must fulfill applicable standards and local
regulations.

A video describing the installation process, is supplied with each ÄKTAprime plus system.

For detailed information on Installation, see ÄKTAprime plus User Manual.

3.1

Site requirements

Requirement

Parameter

100-240 V, 50-60 Hz

Electrical power

4°C to 40°C

Ambient temperature

Stable laboratory bench e.g. 120 × 80 cm

Placement

20% to 95%, non-condensing

Humidity

3.2

Transport

The equipment can be transported on a trolley capable of supporting at least 20 kg.

NOTICE

Lift the instrument in the upright position. Do not use the fraction-
ation arm as a lifting handle.

Before moving the system:

•

disconnect all cables and tubing connected to peripheral components and liquid
containers.

•

remove any loose items from the top of the instrument.

•

grasp the instrument firmly by placing the fingers under the base of the main unit
and lift.

For more information on transport, see ÄKTAprime plus User Manual.

ÄKTAprime plus Operating Instructions 28-9597-89 AB

3 Installation

Содержание AKTAprime plus





































































Результаты поиска

Содержание AKTAprime plus

Отзывы:

Бренды по названию

Популярные бренды

GE AKTAprime plus, Руководство по эксплуатации

Результаты поиска

Содержание AKTAprime plus

Отзывы:

Бренды по названию

Популярные бренды