![background image](http://html.mh-extra.com/html/ge/ahqq06/ahqq06_owners-manual_122392004.webp)
4
49-5000488 Rev. 0
USING THE
AIR CONDITIONER
Controls
7KLVVHFWLRQH[SODLQVKRZWRRSHUDWHWKLVDLUFRQGLWLRQHU
IMPORTANT:
When you turn off the air conditioner, either at the control
panel or with the remote control, wait at least 3 minutes
before turning it back on. This prevents the compressor
from overloading. This 3 minute delay also applies when
switching from cool mode to fan and back.
NOTE:
There is a built in 3 minute delay. You may notice
the compressor might not start right away. This was
designated to protect the unit.
Do not operate your air conditioner in the Cool Mode when
the outside temperature is below 61° F (16° C). This inside
evaporator coil will freeze up, and the air conditioner will not
operate properly.
NOTE:
When the air conditioner is first plugged in, the
LED display will show “88” for 3 seconds. After the air
conditioner is turned on for the first time, the display will
show the temperature 72° F and the fan will automatically
set the Quiet speed and the Mode indicator will show
ENERGY SAVE.
NOTE:
To switch the temperature display between
Fahrenheit (°F) and Celsius (°C), the air conditioner must
be plugged in and turned on. On the control panel on the
IURQWRIWKHDLUFRQGLWLRQHUSUHVVWKH83DQG'2:1EXWWRQ
at the same time and hold for 3 seconds. Press F/C button
on remote control to switch between Fahrenheit (°F) and
Celsius (°C).
NOTE:
Each time this ENERGY STAR qualified air
conditioner is turned on, it will operate in energy save mode
per the EPA requirements. You can select any other mode
to satisfy your needs.
Features and appearance will vary.
Temp.
Time
FAN
E-SAVE
COOL
DEHUM.
HIGH
MED
QUIET
ON
SLEEP
CLEAN FILTER
OFF
MODE
SPEED
TIMER
FILTER
RESET
+
-
POWER
Hr
°F/°C
AUTO
Controls
1. MODE
1. Press MODE until you see the indicator light come on
QH[WWRWKHGHVLUHGVHWWLQJ
2. Choose Fan, Cool, Energy Save, or Dehum.
Fan - Only the fan runs. Press SPEED to select High,
Med or Quiet fan speed. The display shows the current
room temperature.
NOTE:
in fan mode, the temperature
cannot be set.
Energy Save - In this this mode the fan runs only when
cooling is needed. The fan will run for 3 minutes after
the compressor shuts off. The fan then cycles on for 2
minutes at 10 minute intervals until the temperature in
the room is above the set temperature. The compressor
then turns back on.
Cool - Cools the room. Press SPEED to select High,
Med, Quiet or Auto Cool fan speed. Press the TEMP/
TIME
+
or
-
button to adjust the temperature. The fan
will run continuously in cool mode.
Dehum - Aids in removing humidity from the room.
Dehum mode cannot be used to cool room.
NOTE:
In Dehum mode, when the set temperature is
close to ambient temperature, the compressor may stop
and the fan will run in Quiet speed only.
2. SPEED
1. Press SPEED until you see the indicator light come
RQQH[WWRWKHGHVLUHGVHWWLQJ
2. Choose High, Med, Quiet, or Auto Cool
+,*+)RUPD[LPXPFRROLQJ
MED - For normal cooling.
48,(7)RUPLQLPXPFRROLQJDQGQRLVH
$872&22/$GMXVWVWKHIDQVSHHGDXWRPDWLFDOO\WR
provide ideal cooling based on the room temperature.
Содержание AHQQ06
Страница 16: ...16 49 5000488 Rev 0 Notes NOTES ...
Страница 34: ... 49 5000488 Rev 0 Notas NOTAS ...