GE 916-102A3 Скачать руководство пользователя страница 15

Страница: 15 / 40

September 2007

HygroTrace Moisture Transmitter

The Default Display

Figure 6 on page 11 shows the normal, default display of the

HygroTrace

/TFM.

•

Menu Prompt Area

- Titles, prompts, status displayed here.

•

Measurement

- 3 ½ digits (0 - 1999). Automatic decimal

placement based on range.

•

Unit Symbol

- ppb = Parts Per Billion water by volume.

•

Keypad Lock Indicator

- Unlock sequence required to modify

settings.

•

Measurement Progress Bar

HygroTrace

takes

~2 minutes to acquire data and complete the measurement.
The progress bar gives a visual indication of the measurement
status.

•

Warning/Error Indicator

- In the absence of an error, this

region is blank.

Errors

that effect the quality of the

measurement (e.g. heater failure) are indicated in

ALL

CAPITAL

letters.

Warnings

that indicate problems detected

with the measurement are indicated in

Mixed Case

letters.

Refer to Table 3 below.

Table 3: Warning/Error Messages

No.

Label

Type

Description

Status OK

----

No Errors detected.

Sns Ovr Rng

WARN

The calculated PPBv value is greater
than the highest calibration point,
and is an extrapolation.

Acquiring...

WARN

Displayed at startup while the

HygroTrace

collects data for the first

measurement.

101

HTR FAIL LO ERROR

The heater failed to reach the desired
temperature in the time allotted.

102

HTR FAIL HI ERROR The heater exceeded 200°C.

204

Sns Too Wet

WARN

The sensor is exposed to excessive
moisture conditions.

Содержание 916-102A3









































Результаты поиска

Содержание 916-102A3

Отзывы:

Похожие инструкции для 916-102A3

Бренды по названию

Популярные бренды

GE 916-102A3, Руководство пользователя

Результаты поиска

Содержание 916-102A3

Отзывы:

Похожие инструкции для 916-102A3

Бренды по названию

Популярные бренды