GE 700 VA Скачать руководство пользователя страница 2

Страница: 2 / 16

Contents

Safety rules ..................................................................................................................... 3

Introduction .................................................................................................................... 3

Switching off and unplug the battery................................................................. 4

Remove top cover of the UPS................................................................................. 5

Remove dangerous voltage .................................................................................... 6

Unplug the control board......................................................................................... 8

Programmer plug-in................................................................................................... 9

Firmware update .......................................................................................................11

Closing and testing....................................................................................................13

Modifications reserved

ISG_VHS_FRM_UPD_XGB_V010.doc

Содержание 700 VA
















