background image

14

15

FCC Warning

Any unauthorized changes or modifications to the equipment 
would void the user’s warranty and may conflict with both 
state and federal laws. The Choice Alert system complies with 
part 15 of the FCC rules. Operation is subject to the following 
conditions:

1)

 The Choice Alert system may not cause  

harmful interference.

)

 The Choice Alert system may accept any interference 

received including interference that may cause  
undesired operation.

NOTE: 

This equipment has been tested and found to  

comply with the limits for a Class B digital device, pursuant to 
Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and 
can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful  
interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more 
of the following measures: 
 

– Reorient or relocate the receiving antenna.

 

– Increase the separation between the equipment  

 

   and receiver.

 

– Connect the equipment into an outlet on a circuit  

 

   different from that to which the receiver  

 

   is connected.

 

– Consult the dealer or an  

 

   experienced radio/TV technician for help

Содержание 45132

















Отзывы:

Похожие инструкции для 45132