background image

Telephone Jack Requirements

To use this phone, you need an RJ11C type modular telephone 

jack, which might look like the one pictured here, installed in 

your home. If you don’t have a modular jack, call your local 

phone company to find out how to get one installed.

Digital Security System

Your cordless phone uses a digital security system to protect against false ringing, 

unauthorized access, and charges to your phone line.
When you place the handset in the base, the unit verifies its security code. After power 

outage or battery replacement, you should place the handset in the base for about 20 

seconds to reset the code.

INSTALLATION NOTE:

 Some cordless telephones operate at frequencies that 

may cause or receive interference with nearby TVs, microwave ovens, and VCRs. 

To minimize or prevent such interference, the base of the cordless telephone 

should not be placed near or on top of a TV, microwave ovens, or VCR. If 

such interference continues, move the cordless telephone farther away from 

these appliances.

Certain other communications devices may also use the 5.8 GHz frequency for 

communication, and, if not properly set, these devices may interfere with each 

other and/or your new telephone. If you are concerned with interference, 

please refer to the owner’s manual for these devices on how to properly set 

channels to avoid interference. Typical devices that may use the 5.8 GHz 

frequency for communication include wireless audio/video senders, wireless 

computer networks, multi-handset cordless telephone systems, and some long-

range cordless telephone systems.

Installation 

Important Installation Guidelines

•   Avoid sources of noise and heat, such as motors, fluorescent lighting, microwave 

ovens, heating appliances and direct sunlight.

•   Avoid areas of excessive dust, moisture and low temperature.
•   Avoid other cordless telephones or personal computers.
•   Never install telephone wiring during a lightning storm.
•   Never install telephone jacks in wet locations unless the jack is specifically designed 

for wet locations.

•   Never touch non-insulated telephone wires or terminals, unless the telephone line 

has been disconnected at the network interface.

•   Use caution when installing or modifying telephone lines.

Installing the Phone

Base Station

1.  Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and place 

your cordless telephone on a level surface, such as a desktop or tabletop, or you 

may mount it on the wall.

2.  Install the handset battery.

CAUTION:

 To reduce the risk of fire or personal injury, use only the 

battery 5-2548, which is compatible with this unit.

NOTE:

 You must connect the handset battery before use.

•   Plug the battery pack cord into the jack located inside the battery compartment, then 

place the battery pack inside the battery compartment.

•    Put the battery compartment door back on.
3.  Plug one end of the telephone line cord into the TEL LINE jack on the bottom of the 

base and the other end into a modular jack.

Introduction

CAUTION: 

When using telephone equipment, there are basic safety 

instructions that should always be followed. Refer to the IMPORTANT 

SAFETY INSTRUCTIONS provided with this product and save them for 

future reference.

Your Call Waiting Caller ID phone stores and displays specific information, provided 

by your local telephone company, to subscribers of Caller ID or similar caller 

identification services.
Your Call Waiting Caller ID phone enables you to:
•  Identify callers before you answer the phone.
•  View the time and date of each incoming call.
•  Record up to 40 Caller ID messages sequentially in each handset.
•  Know who called while you were away.
To get the most from your new phone, we suggest that you take a few minutes right 

now to read through this user’s guide. 

IMPORTANT:

 In order to use all of the features of this unit, you must subscribe 

to either the standard Name/Number Caller ID Service or Call Waiting Caller ID 

Service. To know who is calling while you are on the phone, you must subscribe 

to Call Waiting Caller ID Service.

IMPORTANT:

 Because cordless phones operate on electricity, you should have 

at least one phone in your home that isn’t cordless, in case the power in your 

home goes out.

IMPORTANT:

 You can only use 

one

 handset at a time and there is 

NO

 

conference and intercom features for these units.

 

Base Layout

5.8 GHz Dual Handset Call Waiting 

Caller ID Cordless Telephone System 

User’s Guide

25841

Equipment Approval Information

Your telephone equipment is approved for connection to the Public Switched Telephone 

Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the 

Technical Requirements for Telephone Terminal Equipment published by ACTA.

Notification to the Local Telephone Company

  On the bottom of this equipment is a label indicating, among other information, the 

US number and Ringer Equivalence Number (REN) for the equipment. You must, 

upon request, provide this information to your telephone company.

  The REN is useful in determining the number of devices you may connect to your 

telephone line and still have all of these devices ring when your telephone number 

is called. In most (but not all) areas, the sum of the RENs of all devices connected 

to one line should not exceed 5. To be certain of the number of devices you may 

connect to your line as determined by the REN, you should contact your local 

telephone company.

  A plug and jack used to connect this equipment to the premises wiring and 

telephone network must comply with the applicable FCC Part 68 rules and 

requirements adopted by the ACTA. A compliant telephone cord and modular plug is 

provided with this product. It is designed to be connected to a compatible modular 

jack that is also compliant. See installation instructions for details.

4.  Set the RINGER switch (on the handset) to ON.
5.  Plug the AC power adaptor into the electrical outlet and the DC connector into the 

jack on the bottom of the base.

6.  Place the handset in the base cradle. The charge/in use indicator turns on, verifying 

the battery is charging.

7.  Allow the phone to charge for 16 hours prior to first use. If you don’t properly charge 

the phone, battery performance is compromised.

CAUTION:

 Use only the ATLINKS USA, Inc. 5-2501 (black) power 

converter that came with this unit. Using other power converters may 

damage the unit.

NOTE :

 The phone is tone dial only and does not support pulse dial mode.

Extra Charging Cradle

1.  Plug the AC power adaptor of the extra charging cradle into the electrical outlet.
2.  Install the handset battery as item 2 described above.
3.  Place the handset in the extra charging cradle. The charge indicator turns on, 

verifying the battery is charging. 

4.  Allow the phone to charge for 16 hours prior to first use.

Wall Mounting

NOTE:

 For best results, charge the phone on a flat surface before you mount it 

on the wall.

1.  Slip the mounting holes (on the back of the base) over the wall plate posts, and slide 

the unit down into place. (Wall plate not included.)

2.  Place the handset on the base cradle.

Registration 

YOU MUST REGISTER BOTH HANDSETS TO THE MAIN BASE BEFORE USE!

a) 1st handset - The 1st handset being charged on the main base station will 

automatically register after 16 hours of charging.
b) 2nd handset - After the 2nd handset has charged for 16 hours on the extra charger, 

place it on the main base station for 20 seconds, it will then automatically register.

NOTE:

 

PLEASE REGISTER

 will show on the display if the handsets have not 

been registered. Once the handsets have completed registration successfully, 

HANDSET 1

 and 

HANDSET 2

 will show on the handset’s display.

NOTE:

 In case of a power failure, the handsets may display 

UNAVAILABLE

 when 

the talk/end/call back button is pressed. You must then place both handsets on 

the 

main base cradle

 for 20 seconds to re-register.  

Setup

There are four programmable menus available: Language, Area Code, Ringer Tone, and 

Default Setting.
During programming, you may press the flash/prog button at any time to go to the 

next option. To exit the menu, keep the previous setting and return to the standby 

mode, press the *exit button.

Display Language

1.  Press the flash/prog button until 

>1ENG 2FRA 3ESP

 shows in the display. 

1ENG

 is 

the default.

2. Use the Caller ID/vol (- or +) button or the touch-tone pad on the handset to enter 

your selection.

3.  Press flash/prog again to save.

Local Area Code

1.  Press the flash/prog button until 

AREA CODE - - -

 shows in the display. 

- - - 

is 

the default. 

2. Use the touch-tone pad on the handset to enter your three digit area code.
3.  Press flash/prog again to save.

NOTE:

 If you make a mistake, press the del/chan button to erase a  

wrong number.

Ringer Tone

1.  Press the flash/prog button until 

RINGER TONE 

1

 shows in the display. 

is the 

default.

2. Use the Caller ID/vol (- or +) button or the touch-tone pad on the handset to scroll to 

1, 2, or 3

.

3.  Press flash/prog to save.

Default Setting

1.  Press the flash/prog button until 

DEFAULT 

NO

 shows in the display. 

NO

 is  

the default.

2.  Use the Caller ID/vol (- or +) button on the handset to scroll to 

YES

 or 

NO

.

3. Press flash/prog to save. You will hear a confirmation tone.

Cordless Phone Basics

IMPORTANT:

 You can only use 

one

 handset at a time and there is 

NO

 

conference and intercom features for these units.

 

Charge/In Use Indicator

The phone is ON when the talk/end/call back indicator on the handset and the charge/in 

use indicator on the base is lit. The handset and base indicators flash when you receive 

a call.

Answering a Call

1.  When the phone rings, pick up either handset and press the talk/end/call back button.
2.  When finished, press the talk/end/call back button again or place the handset on 

either the base cradle or the extra charger to hang up.

Making a Call

1.  Pick up either handset and press the talk/end/call back button. Wait for the dial tone. 

The call timer starts counting minutes and seconds in the display.

2.  Dial a telephone number.
3.  When finished, press the talk/end/call back button again or place the handset on 

either the base cradle or the extra charger to hang up.

NOTE:

 You can only use one handset at a time and there is no conference 

and intercom features for these units.

 UNAVAILABLE

 will be displayed if other 

handset is in talk mode.

Pre-dialing

1.  Make sure the phone is 

OFF

 (not in TALK mode).

2.  Dial a telephone number (the number you dial shows in the display).

NOTE:

 If you make a mistake dialing the number, use the del/chan button to 

backspace and erase the wrong number, and enter the correct number.

3.  Press the talk/end/call back button on that handset. The number automatically dials 

and the call timer starts counting the minutes and seconds in the display.

4.  When finished, press the talk/end/call back button again to hang up.

NOTE : 

You may enter up to 32 pre-dial digits.

Call Transfer

During an external call, you may transfer the external call to another handset.
1.  Press trans button on the originating handset. 

TRANSFERRING

 shows in the display. 

Both handsets will be paged.

2.  Press trans button or talk/end/call back on receiving handset to answer the call.

NOTE:

 To cancel the call transfer, you may press *exit button or 

trans

 button on 

the originating handset.

NOTE:

 If there is no answer within 2 minutes after transferring the call, then 

both handsets will be rung back (callback). If neither handset answers within 30 

seconds, then the external call will be automatically dropped. 

Redial

While the phone is 

ON

 (in TALK mode), press the redial button to redial the last number 

you dialed (up to 32 digits).
   

OR,

While the phone is 

OFF

 (in standby mode), press the redial button and then the  

talk/end/call back button to redial the last number.

Flash

Use the flash/prog button to activate custom calling services such as call waiting, which 

are available through your local phone company.

TIP:

 Don’t use the talk/end/call back button to activate custom calling services 

such as call waiting, or you’ll hang up the phone.

Channel Button

While talking on the phone, it may be necessary for you to manually change the 

channel to improve reception and reduce noise or static on the line. Press and release 

the del/chan button to move to the next clear channel.

Exit

Press the *exit button to cancel any command you initiated.

Finding the Handset

This feature helps locate misplaced handsets.
Press the page button on the base. The handset beeps continuously for about 2 minutes 

until you press the talk/end/call back button on the handset or the page button on 

the base.

NOTE:

 You may still page the handsets when the ringer is off.

Ringer Switch 

The ringer switch is located on the side of the handset, it has two positions, ON and OFF.

Volume

When the phone is 

ON

 (in TALK mode) press the Caller ID/vol (- or +) button to adjust 

the listening level. Choose from four volume settings. VOL 1 is the lowest volume and 

VOL 4 is the highest volume.

Mute

Use mute during a phone conversation to speak privately and off-line with a third party.
1.  Press the format/mute button. MUTE shows in the display. The party on the 

telephone will not hear you.

2.  Press the format/mute button when finished.

Caller ID (CID)

This unit receives and displays information transmitted by your local phone company. 

This information can include the phone number, date, and time; or the name, phone 

number, date, and time. Each handset can store up to 40 calls for later review.

ATLINKS USA, Inc.

101 West 103rd Street

Indianapolis, IN 46290

© 2005 ATLINKS USA, Inc. 

Trademark(s) ® Registered

Marca(s) Registrada(s)

Model 25841 

00006031 (Rev. 0 Dom E) 

05-34 

Printed in China

Handset Layout

Modular 

telephone 

line jack

Wall plate

2 Handsets

2 Belt clips

AC power 

converter

2 Handset 

batteries

2 Battery 

compartment doors

Time

Date

Number of calls

Caller ID name

Caller ID phone number

SEE MARKING ON BOTTOM / BACK OF PRODUCT

RISK OF ELECTRIC SHOCK

            DO NOT OPEN

WARNING:

 TO

PREVENT FIRE OR

ELECTRICAL SHOCK

HAZARD, DO NOT

EXPOSE THIS

PRODUCT  TO RAIN

OR MOISTURE.

THE LIGHTNING

FLASH AND ARROW

HEAD WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

“DANGEROUS

VOLTAGE” INSIDE

THE PRODUCT.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR

BACK). NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL.

THE EXCLAMATION

POINT WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU  OF

IMPORTANT

INSTRUCTIONS

ACCOMPANYING

THE PRODUCT.

CAUTION:

Notes  

•  This equipment may not be used on coin service provided by the 

telephone company.

•  Party lines are subject to state tariffs, and therefore, you may not be able to use 

your own telephone equipment if you are on a party line. Check with your local 

telephone company.

•  Notice must be given to the telephone company upon permanent disconnection 

of your telephone from your line.

•  If your home has specially wired alarm equipment connected to the telephone 

line, ensure the installation of this product does not disable your alarm 

equipment. If you have questions about what will disable alarm equipment, 

consult your telephone company or a qualified installer.

Rights of the Telephone Company 

  Should your equipment cause trouble on your line which may harm the telephone 

network, the telephone company shall, where practicable, notify you that temporary 

discontinuance of service may be required. Where prior notice is not practicable and 

the circumstances warrant such action, the telephone company may temporarily 

discontinue service immediately. In case of such temporary discontinuance, the 

telephone company must: (1) promptly notify you of such temporary discontinuance; 

(2) afford you the opportunity to correct the situation; and (3) inform you of your 

right to bring a complaint to the Commission pursuant to procedures set forth in 

Subpart E of Part 68, FCC Rules and Regulations.

  The telephone company may make changes in its communications facilities, 

equipment, operations or procedures where such action is required in the operation 

of its business and not inconsistent with FCC Rules and Regulations. If these changes 

are expected to affect the use or performance of your telephone equipment, the 

telephone company must give you adequate notice, in writing, to allow you to 

maintain uninterrupted service.

Licensing

Licensed under US Patent 6,427,009.

Hearing Aid Compatibility (HAC)

This telephone system meets FCC standards for Hearing Aid Compatibility.

US NUMBER IS LOCATED ON THE CABINET BOTTOM

REN NUMBER IS LOCATED ON THE CABINET BOTTOM

charge/in use

(indicator)

page (button)

charge

(indicator)

Base

Before You Begin

Parts Checklist

Make sure your package includes the items shown here.

RED WIRE

BLACK WIRE

BATTERY

PRESS DOWN

FIRMLY

display

talk/end/call back 

(button)

del/chan 

(delete/channel button)

redial 

(button)

*exit 

(button)

#pause 

(button)

flash/prog 

(flash/program button)

trans 

(transfer button)

format/mute 

(button)

headphone jack

mem

(memory button)

ringer 

(switch)

Handset Charge Cradle Layout

Call Waiting Caller ID

Provided you subscribe to Call Waiting Caller ID service from your phone company, 

you are able to see who is calling while you are on the phone when you hear the call 

waiting beep. The caller identification information appears in the display after you hear 

the tone.
•  When you hear the call waiting beep in the handset receiver, press the flash/prog 

button to put the current call on hold and answer the incoming call.

IMPORTANT:

 In order to use this unit’s Caller ID features, you must subscribe 

to either the standard Name/Number Caller ID Service or Call Waiting Caller ID 

Service. To know who is calling while you are on the phone, you must subscribe 

to Call Waiting Caller ID Service.

Receiving and Storing CID Records

When you receive a call, the information is transmitted by the phone company to your 

Caller ID telephone between the first and second ring. 
When the memory is full, a new call automatically replaces the oldest call in memory. 

NEW 

appears in the display for calls received that have not been reviewed.

NOTE: 

Check with your local phone company regarding name service availability.

Reviewing CID Records

As calls are received and stored, the display is updated to let you know how many calls 

have been received.
•  Press the Caller ID/vol (-) to scroll through the call records from the most recent 

to the oldest.

Caller ID/vol (-) 

(caller ID/volume 

- button)

Charge cradle

Line cord

Caller ID/vol (+) 

(caller ID/ 

button)

Отзывы: