Focus adjustment
To adjust the camera zoom and focus, see Figure 5 and do
the following:
Table 3: Description of zoom and focus adjustment in Figure 5
1.
Zoom ring thumbscrew for VA2 and focus ring for VA9
lens.
2.
Focus ring thumbscrew for VA2 and zooming ring for VA9
lens.
1. Loosen the zoom ring thumbscrew.
2. Turn the zoom ring to set the desired zoom.
3. Tighten the zoom ring thumbscrew.
4. Loosen the focus ring thumbscrew.
5. Turn the focus ring to set the desired focus.
6. Tighten the focus ring thumbscrew.
Connect the monitor
Program the cameras by attaching a standard video
monitor to the system.
To connect the monitor, do the following:
1. Plug the monitor output cable (Figure 2) to the video
monitor output connector (Figure 1).
2. Connect the BNC cable to the video monitor.
3. Press Enter (Figure 3) to display the Setup menu.
Programming
The camera is configured through the setup menus which
appear on-screen. See Figure 6.
To access and navigate the menus, press and hold the
center of the OSD control pad (Figure 3). Press Up or Down
on the control pad to move between items, and press Enter
(center of the control pad) to select the item. Press Right or
Left on the control pad to select the different options
available for the item.
You can return to the previous menu from any of the
menus (except the Main menu) by selecting the
Previous
page
option.
The menu map is shown on the back page.
Refer to the User Manual for detailed programming
instructions.
Table 4: Main menu options
Menu option
Description
Preset Preset
settings.
Setup
Camera ID, Line Lock, motion detection, and
WDR settings.
Viewing
Flip and resolution settings
Exposure
AGC, AE preferences, range control, shutter limit,
frame RPT, and B/W control settings.
White balance White balance settings.
Save/Restore
Save and restore user and factory settings.
Specifications
Electrical
Power Input
12 VDC or 24 VAC
Power consumption
3W (DC); 2.4 W (AC)
Environmental and physical
Weight
33.8 oz. (958 g)
Dimensions
5.22 x 4.11 in. (133 x 105 mm)
Operating Temperature
-58 to +122°F ( + -50 to +50°C)
Weather resistant
IP66
Regulatory information
Certification
N0000
FCC compliance
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and
used in accordance with the instruction
manual, may cause harmful interference to
radio communications.
You are cautioned that any changes or
modifications not expressly approved by the
party responsible for compliance could void
the user ’s authority to operate the equipment.
European Union
directives
1999/5/EC (R&TTE directive): Hereby, GE
Security declares that this device is in
compliance with the essential requirements
and other relevant provisions of Directive
1999/5/EC.
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European
Union. For proper recycling, return this
product to your local supplier upon the
purchase of equivalent new equipment, or
dispose of it at designated collection points.
For more information see:
www.recyclethis.info.
2004/108/EC (EMC directive): Non-European
manufacturers must designate an authorized
representative in the Community. Our
authorized manufacturing representative is:
GE Security B.V., Kelvinstraat 7,
6003 DH Weert, The Netherlands.
Contact information
For contact information, see our Web site:
www.gesecurity.com
EMEA: For contact information, see our Web site:
www.gesecurity.eu
P/N XP3DNR092009 • REV 01.00 • ISS 03SEP09
3 of 4
