GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 240

background image

Maintenance and checkout

129

2062973-002

10 Maintenance and checkout

This chapter specifies the checkout procedure and the maintenance activities to be performed
to the patient monitor after corrective maintenance and during annual planned maintenance.

WARNING

Only perform maintenance procedures specifically described in the manual.

WARNING

Planned maintenance should be carried out annually. Failure to implement

the recommended maintenance schedule may cause equipment failure and
possible health hazards.

NOTE: The manufacturer does not, in any manner, assume the responsibility for performing the
recommended maintenance schedule, unless an Equipment Maintenance Agreement exists.
The sole responsibility rests with the individuals, hospitals, or institutions utilizing the device.
NOTE: Refer to Module Frames and Modules Technical Manual for corrective and planned
maintenance checkout procedures of the parameter modules.
NOTE: Refer to the PDM section in the Module Frames and Modules Technical Manual for the
battery maintenance procedure of the PDM battery.

Corrective maintenance

Service personnel shall perform the following checkout procedure steps after any corrective
maintenance, before taking the monitor back into clinical use:

Performed service activity

Required checkout procedure

Visual
inspections

(section 10.1)

Electrical
safety test
(section 10.2)

Functional check

(section 10.3)

After detaching, replacing or
upgrading:
- Recorder Unit FRU / Upgrade
- E-module Board FRU / Upgrade
- Module Frame Assembly FRU

Yes

Yes

- 10.3.1 Start-up
- 10.3.3 PSM / PDM

- 10.3.4 E-module identification
- 10.3.13 Recorder

After detaching or replacing:
- PDM Docking Mechanism FRU
- Module Frame Cover Unit Set FRU

Yes

No

- 10.3.1 Start-up
- 10.3.3 PSM / PDM

After detaching, replacing or
upgrading:
- Standard Interface Board FRU
- Advanced Interface Board FRU /

Upgrade

Yes

Yes

- 10.3.1 Start-up
- 10.3.6 Mouse
- 10.3.7 Alphanumeric

- 10.3.9 MC Network and S/5

After replacing or upgrading:
- Wireless LAN FRU / Upgrade

Yes

No

- 10.3.1 Start-up
- 10.3.10 Wireless LAN

After replacing:
- Mains Fuses FRU
- Battery FRU

Yes

No

- 10.3.1 Start-up

«
...
135
136
137
138
139
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B650

Бренд: GE Страницы: 2

Druck DPI 620 Genii

Бренд: GE Страницы: 154

Arize Element Top Light

Бренд: GE Страницы: 2

Бренд: Datex-Ohmeda Страницы: 104

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 166

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 340

Бренд: Datavideo Страницы: 28

Бренд: Haaga Страницы: 31

Бренд: Taylor Страницы: 41

Бренд: Zennio Страницы: 3

STOMAMED COL-160

Бренд: Orliman Страницы: 12

Бренд: Fri-Jado Страницы: 48

Бренд: Janschitz Страницы: 40

Бренд: Dangerous power Страницы: 38

Бренд: Clas Ohlson Страницы: 20

Бренд: GLITCHMACHINES Страницы: 8

MiNiSTUDIO PERSONAL US-32

Бренд: Tascam Страницы: 11

2 - Person Chest Press

Бренд: Paris Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды