background image

The only maintenance required by the operator is to periodically clean
the heat shoes. The following procedure will help keep the heat shoes
free of adhesive that has been deposited along the edge of the
laminating film.

CAUTION: THE FOLLOWING PROCEDURE IS PERFORMED
WHILE THE LAMINATOR IS HOT. USE EXTREME
CAUTION.

WARNING: Do not apply cleaning fluids or solvents to
the rollers.

WARNING: Do not attempt to laminate adhesives
marked ‘Flammable’.

Remove the film from the laminator following the procedure
outlined in the section FILM LOADING AND THREADING.

Preheat the laminator until the READY LAMP (

) illuminates.

Clean the top and bottom heat shoes with a soft cloth.

Follow the procedure in section FILM LOADING AND THREADING,
Method Using Film Threading Card to reload the laminator.

NOTE: 

Do not use metal scouring pads to clean the heat shoes!

WARNING: 

Do not laminate glitter and/or metallic items. Damage to the
rollers may result.

4

3

2

1

5

Installation

• Shipping damage should be brought to the immediate attention of the

delivering carrier.

• Place the laminator on a stable flat surface capable of supporting

44lbs. The surface should be at least 30” high to assure comfortable
positioning during operation. All four rubber feet should be on the
supporting surface.

• Connect power cord to an appropriate power source. Avoid

connecting other equipment to the same branch circuit to which the
laminator is connected as this may cause nuisance tripping of the
circuit breaker or blown fuses.

• The laminator should be positioned to allow exiting film to drop freely

to the floor. Accumulation of laminate as it exits the laminator may
cause film to wrap around the rollers, causing a jammed condition.

• Avoid placing laminator near sources of heat or cold. Avoid locating

the laminator in the direct path of forced, heated or cooled air.

WARNING: THIS IS NOT A TOY - DO NOT ALLOW CHILDREN TO OPERATE THIS LAMINATOR!

Service

Perform only the routine maintenance procedures referred to in these
instructions.

Do not attempt to service or repair the laminator.

Unplug the unit and contact an authorized GBC service representative
for any required repairs or one or more of the following has occurred:

• The power supply cord or attachment plug is damaged.

• Liquid has been spilled into the laminator.

• The laminator is malfunctioning after being mishandled.

• The laminator does not operate as described in these instructions.

Caring for the Ultima 35 EZload


Содержание Ultima 35 EZload












Отзывы: