Gateway M460 Скачать руководство пользователя страница 6

Страница: 6 / 70

Replacing Gateway Notebook Components

www.gateway.com

Important

This service guide is not intended to be

provided to individual users or

consumers. It cannot be provided to

anyone other than an authorized service

provider.

Important

For information on the notebook’s

general maintenance, technical support,
safety notices, and regulatory notices, see

the notebook’s user guide.

Important

If you have suggestions regarding the

content of this guide, send an e-mail with
the subject “Service Guide Comments” to

[email protected].

Use this service guide to help plan maintenance tasks for the following Gateway
notebooks:

■

M460

■

M465-E

■

MX6700

All tasks covered in this guide can be performed by an

authorized field

technician

without jeopardizing the notebook’s warranty.

Identifying the notebook model

Caution

It is important that you use the correct

service guide for the notebook. Failure to

follow the approved tasks for the

notebook model may result in damage to

the notebook.

The label on the bottom of the notebook contains information that identifies
the notebook model and its features.

Website: www.gateway.com
Online Support:

www.gateway.com/support

Tech Support Phone:

Hours:
Model:
S/No:

Содержание M460







































































Результаты поиска

Содержание M460

Отзывы:

Похожие инструкции для M460

Бренды по названию

Популярные бренды

Gateway M460, Руководство по обслуживанию

Результаты поиска

Содержание M460

Отзывы:

Похожие инструкции для M460

Бренды по названию

Популярные бренды