EN
EN
14
15
6.
Keeping the water at the set temperature:
Press the “Keep Warm” button. If
required, set the desired temperature (40-99°C; 104-210°F) via the adjustment
buttons “+” or “–”. The kettle heats the water to the set temperature shown on the
display and keeps this temperature up to 2 hours. Thereafter, the heating cycle
is terminated automatically.
NOTE
Via the “Keep Warm” button, you may switch the keep warm function on and
off. The function is activated, when the keep warm icon is shown on the display.
IMPORTANT -
Ensure that there are always at least 200ml of water in the kettle.
Especially, when keeping the water warm at high temperature for a prolonged
time, the filling level may drop significantly due to evaporation.
Intermediately
contol the filling level and add water in time.
WARNING
– Please keep in mind that the appliance is no temperature
measuring device. The accuracy of the displayed temperature is adapted to its
intended use for heating water and not suited for special purpose (e.g. preparing
food and beverages for invalid persons or babies). Always check the temperature
before feeding and/or consuming.
7.
After usage:
Press the ON/OFF button for switching off the appliance. If you
do not wish to use the appliance again, unplug the appliance. Remove the
kettle from the power base and wait until the water stops boiling. Pour the water
carefully. Do not leave the water cool down within the kettle, to avoid excessive
build-up of scale deposits in the kettle.
NOTE
You may place the kettle onto the power base, when the kettle is not in use.
However, always unplug the power base, when the appliance is not in use.
SOLVING PROBLEMS
Sollten während der Arbeit Probleme auftreten, dann finden Sie hier Lösungen.
Problem
Reason
The Solution
Emergency stop required?
Immediately unplug the appliance.
The appliance is plugged
in but the display stays
completely dark.
No connection to the
power supply.
– Is the power plug connected correctly to the power outlet?
– Is the power cord undamaged?
– Check the electrical connectors (base, kettle and power
plug) against pollution, discolouration and corrosion.
– Is the power outlet live? Connect a lamp.
Problem
Reason
The Solution
A severe problem occurred. Immediately unplug the appliance. Get in contact with your
vendor.
The display is illuminated
but the kettle does not
heat.
The kettle is not placed
correctly on the power
base.
– Turn the kettle a little.
– Check the electrical connectors (base, kettle and power
plug) against pollution, discolouration and corrosion.
Do not attempt to operate the appliance with the
electrical connectors or power cord damaged in
any way!
Get in contact with your vendor.
No function selected.
You need to press at least 1 button for starting a function.
This holds even for warming up the water to the default tem-
perature (40°C). In this case, press an adjustment button
(“+” or “–”; see: ‘Operation’).
The boil-dry protection has
been triggered. “E3” is
shown on the display. The
kettle is empty.
Remove the kettle from the base. Open the lid and wait
approx. 15 minutes. Then try again.
Always ensure that the filling level reaches
the “MIN / 0.2L” marking (approx. 200ml).
The display tones down
during operation.
No entry has been made
for more than approx. 6
minutes
The energy saving mode is activated (see: ‘Properties of
Your Water Kettle’). This is normal operation.
Large amounts of steam
escape from the spout. The-
re may be a bubbling noise.
To little water in the
kettle.
For operation, always ensure that at least 200ml water are
in the kettle (“MIN / 0.2L” marking; approx. 1 inch above
the heating plate). Add a sufficient amount of water in time.
Water splashes out at the
upper rim of the kettle.
The kettle is overfilled.
Unplug the appliance and carefully remove the kettle from
the base. Thoroughly dry the base and working space.
Pour out some water. The filling level may not protrude
the “MAX / 1.0L” marking (at least 1 inch below the
rim of the kettle).
Do not overfill the kettle!
The heating cycle is termi-
nated, before the water
is boiling.
Too little water in the
kettle.
FIll the kettle with a sufficient amount of water. The fil-
ling level must lie between 0.2L and 1.0L.
When using the keep warm function at high
temperature, please ensure to check the fil-
ling level in time.
Too many scale deposits
on the heating plate.
To avoid overheating, descale the kettle in time (see:
‘Care and Cleaning’).
The electical connectors
of the base or kettle are
damaged, moist or burnt.
Immediately unplug the appliance. Return the appliance to
an authorised service centre for examination and repair.
Always keep the electrical connectors abso-
lutely dry.
