Gasmate ODYSSEY 2T Скачать руководство пользователя страница 21

21

20

OPERATION

 IMPORTANT

The hood must be in the open position for lighting.
Do not smoke at any time when attempting to ignite 
the barbecue burners.  
Do not leave the barbecue unattended when alight 
or at anytime during use.

BURNER OPERATION & IGNITION SYSTEM CHECK

Problem

Possible Reason

Solution

Burner will not ignite

Control knob is closed

Turn knob to high when lighting

Piezo igniter is faulty

Use a long barbecue match inserted through 
the hole on under side of barbecue

Food is not cooking  
or is taking too long

Burner has gone out

Check that the gas bottle is not empty and re-
ignite the burner

Cooking surface was not given 
enough time to warm up before the 
food was applied

Remove the food and give the burner time to 
warm the cooking surface (5-10 mins)

There is too much food on the 
cooking surface

Cook smaller portions

OPERATING PROCEDURE 

Cooking

The control knob can be turned from ‘HIGH’ to ‘MED’ or 
‘LOW’ depending on the heat required.
With the hood down the burners must only be used on 
‘LOW’.
When cooking with a Wok, remove the Wok Grill Plate 
and ensure the bottom of the Wok does not touch the 
burner, or purchase the Gasmate Odyssey Wok which 
has been designed to meet these requirements.
When roasting with the hood down turn the gas controls 
down to maintain a temperature around 200ºC.

Servicing

Servicing should be conducted every year or sooner if 
required. 
The appliance must only be serviced by an authorised 
person.

Содержание ODYSSEY 2T

























Отзывы: