2
3
2
3
INSTALLATION
Important Safety Rules:
This appliance must only be used in a well ventilated
area.
1. This appliance shall not be installed or used indoors,
in buildings, garages or any other enclosed area.
2.
DO NOT
place articles on or against this appliance.
3.
DO NOT use or store flammable materials near this
appliance.
4. Children and adults should be alerted to the hazards
of high surface temperatures, burns and clothing
ignition.
5. Children should be carefully supervised when they
are in the area of the appliance.
6.
NEVER
hang anything including clothes or other
flammable items on the appliance.
7.
DO NOT
operate this appliance unless it is fully
assembled with reflector in place.
8.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF
THIS APPLIANCE WHILE IT IS IN OPERATION.
9. Installation and repair should be done by a qualified
service person. The appliance must be inspected
before use and at least annually by a qualified
service person. More frequent cleaning may be
required as necessary. It is imperative that control
compartment, burners and circulating air passages
of the appliance and light be kept clean.
Prior to assembling your appliance, the following must be
reviewed. Compliance with the following should result in
satisfactory appliance operation. This instruction manual
should be retained for future reference. The installation
must conform with local codes or authority having
jurisdiction.
1. The appliance is intended for residential and
nonresidential outdoor spaces. The installation
must conform with New Zealand Standard 5261 “Gas
Installations”.
2. Adequate clearance around air openings into the
combustion chamber, clearances from combustible
materials, provisions for accessibility and for
combustion and ventilating air supply must be
maintained at all times when the appliance is
operating.
3. Proper clearance from combustible materials must be
maintained at all times. The minimum clearances are
as follows:
Minimum Clearance from Combustibles:
Sides
600 mm
Rear
600 mm
Ceiling
900 mm
Installation, Operation and Maintenance Instructions
Combustible materials are considered to be wood,
compressed paper, plant fibres, plastic, plexiglas or
other materials capable of being ignited and burned.
Such materials shall be considered combustible even
though flame proofed, fire-retardant treated or plastered.
Additional clearance may be required for glass, painted
surfaces and other materials which may be damaged by
radiant or convection heat.
4. The appliance must be placed on a level and adequate
footing and be readily accessible.
5. The gas manifold supply pressure must be regulated
at 2.75 kPa utilising an approved regulator
(supplied with appliance).
6. The appliance must be inspected before each use, and
at least annually by a qualified service person.
a. The appliance area must be kept clear and free of
combustible materials, gasoline and other
flammable vapours and liquids.
b. Gas orifices and burner must be kept clear of dirt
and cobwebs. Flow of combustion and ventilation
air through the perforated portions of the appliance
must not be obstructed. Cleaning with a soft
brush before use and at least every six months is
recommended.
c. All gas connections should be checked for leaks
utilising a soap solution. Never use a flame for this
purpose.
d. The flame pattern at the emitter grid should be
visually checked whenever the appliance is
operated. If flames extend beyond surface of the
emitter grid or black soot is accumulating on the
emitter grid or reflector, the appliance should
be turned off immediately. The appliance should not
be operated again until the unit is serviced and or
repaired.
e. Any cleaning agent used on the appliance should be
of a non-combustible and non-corrosive nature.
Warm soapy water is ideal. While washing the
appliance, be sure to keep the area around the
burner and pilot assembly dry at all times. If the
gas control is exposed to water in any way, do NOT
try to use it. The appliance should be regularly
cleaned and protected to reduce oxidation, ideally a
cover should be used when not in use.
f. The emitter grid normally does not require cleaning
and should
NEVER be painted. The reflector may
be cleaned, but never painted.
Содержание Infeno GM124-013
Страница 12: ...12 ...
