manualshive.com logo in svg

Gasmate GM172-124, Руководство пользователя

Поделиться
Скачать
Gasmate GM172-124 Скачать руководство пользователя страница 23

23

22

This appliance shall only be used in an above ground open-air situation with natural ventilation, 
without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind 
and natural convection.

Any enclosure in which the appliance is used shall comply with the following:
An enclosure with walls on all sides, but at least one permanent opening at ground level and no 
overhead cover.
Within a partial enclosure that includes an overhead cover and no more than two walls.

Within a partial enclosure that includes an overhead cover and more than two walls, the 

following will apply:
at least 25% of the total wall area is completely open, and
at least 30% of the remaining wall area is open and unrestricted.

In the case of balconies, at least 20% of the total wall area shall be and remain open and 

unrestricted.

SAFE APPLIANCE LOCATIONS

DIAGRAMMATIC REPRESENTATIONS OF OUTDOOR AREAS

The following figures are diagrammatic representations of outdoor areas. Rectangular areas have been 
used in these figures – the same principles apply to any other shaped area.

Gasmate

®

 is a registered trademark of: Sitro Group Australia Pty Ltd www.gasmate.com.au 

    Aber, 

Hamilton, 

N.Z. 

www.gasmate.co.nz

Содержание GM172-124

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды