11
10
ASSEMBLY INSTRUCTIONS
STEP 5
Attach the regulator to your gas cylinder.
STEP 6
Turn on the gas cylinder ensuring that all of the controls
on the BBQ are turned OFF at this point. DO NOT
ATTEMPT TO LIGHT THE BBQ.
STEP 8
If the connection is leaking, bubbles will start to grow in
the soapy solution. If this happens shut off the gas supply
at the cylinder.
STEP 10
The connection is gas tight when no bubbles grow
around the gas connection.
STEP 9
Tighten the connections using a crescent then repeat
steps 7-8.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
STEP 7
Use a solution of soapy water (dishwashing liquid and
water is fine). Brush it on or use a spray bottle as shown in
the drawing. Ensure the connections have a good coating.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
Step 12
Attach the regulator to your gas cylinder.
Step 13
Turn on the gas cylinder ensuring that all of the
controls on the BBQ are turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE BBQ!!.
Step 14
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray
bottle as shown in the drawing. Ensure the
connections have a good coating.
Step 15a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut
off the gas supply at the cylinder.
Step 15b
Tighten the connections using a crescent then
repeat steps 13-14.
Step 15c
The connection is gas tight when no bubbles
grow around the gas connection.
GENERAL ASSEMBLY
CONNECTING & DISCONNECTING TO GAS
SOURCE
Familiarise yourself with the general information and
safety guidelines located at the front of this manual.
CHECK:
1. The cylinder is filled. A sloshing sound will be heard
when shaken.
2. The burner controls are in the ‘OFF’ position.
CONNECTING
1. Ensure cylinder valve is in its full off position.
2. Check for any damage to either the cylinder
connection or the hose. NEVER attempt to use
damaged equipment.
3. When connecting the hose to the cylinder tighten the
nut to a positive stop by hand.
4. Open cylinder valve fully. If a leak can be heard at
either end of the hose turn cylinder off and tighten
joint. Wait 5 minutes before re-testing and use a soapy
water solution to check the joint. If bubbles appear the
connection will need to be re-tightened.
Refer to previous page for more detailed instructions on
connecting the appliance to the cylinder.
DISCONNECTING
1. Ensure the burner control is in the ‘OFF’ position.
2. Ensure cylinder valve is in the full off position.
For storage and cylinder exchange, disconnect hose
at the cylinder only, DO NOT disconnect hose from
appliance.
REGULATOR SAFETY FEATURE
The SafeLok LCC27 regulators fitted to this BBQ (the
part that attaches to the gas cylinder to regulate the flow
of gas) have a safety feature included that restricts gas
flow in the event of a gas leak. You can inadvertently
activate this safety feature without having a gas leak.
This typically occurs when you turn on the gas using
the barbecue control knob before you turn on the
gas cylinder valve. If the gas regulator safety feature
activates, the barbecue will operate with reduced output
as gas flow is restricted.
These steps should be taken first to reset the gas
regulator safety device:
1. Ensure the barbecue lid is off.
2. Turn gas cylinder valve off.
3. Turn off all control knobs.
4. Disconnect the regulator from the gas cylinder.
5. Wait 30 seconds.
6. Reconnect the regulator to the gas cylinder.
7. Leak test the connection using a soapy water solution
Ensure no bubbles appear before proceeding.
8. Slowly open the gas cylinder valve all the way. Do
not put excessive force on the valve at the full open
position, to avoid damaging the valve.
9. Light barbecue as per the instructions provided.
LIGHTING PROCEDURE
Before lighting your barbecue for the first time, read the
instructions fully to ensure the barbecue is assembled
correctly and is ready for use.
BURNER OPERATION & IGNITION SYSTEM
CHECK
1. Remove the lid of the barbecue before attempting to
light the burners.
2. Turn all the control knobs clockwise to “OFF” position.
3. With cylinder valve in “OFF” position turn the control
knob on the far left or far right anti-clockwise to
“HIGH” (a single click is heard). Check for sparking to
the burner.
4. If spark is not evident at the burner ignition point,
check that the ignition lead is firmly attached to the
control and sparker tip.
5. With sparking established turn the cylinder valve ‘ON’.
6. Push down and turn the control knob on the far left
or far right anti-clockwise to “HIGH” again. This will
light the burner. Observe if the burner has lit. If not,
repeat this process.
7. If the burner fails to ignite after several attempts turn
off gas supply at cylinder valve and the control knob
off (clockwise). Wait five minutes before attempting
to relight with ignition sequence.
• IMPORTANT: Before connecting and
disconnecting barbecue to gas source, make sure
burner controls are in ‘OFF’ position.
•
CAUTION:
When the barbecue is not in use, the
gas must be turned off at the cylinder.
• Check that the seals between the appliance
and the gas cylinder are in place and in good
condition before connecting the gas cylinder.
• Do not use this appliance if it has damaged or
worn seals.
• Check performance of burner prior to using.
IMPORTANT: