manualshive.com logo in svg

Gasboy Islander ICR PLUS, Руководство по установке

Поделиться
Скачать
Gasboy Islander ICR PLUS Скачать руководство пользователя страница 58

3-2.3. Safety Distances 

Figure  3-1 shows the safety distances required for the installation of the Islander PLUS adjacent 
to the dispensers.  When mounting the Islander PLUS, a minimum clearance of 18 inches 
(0.5m) between the unit and any of the pumps or the dispensers must be maintained.  This 
clearance allows room for the wiring and maintenance of the system.  

 

Islander PLUS is designed and approved for installation and use at a convenient location at or near 
fuel Island in the appropriate hazardous (classified) location: 

•

 

Where hazardous location is classified as Class 1, Division 2 and it does not extend higher 
than 18 inches (0.5m) from surface and 

•

 

A minimum safety separation of 18 inches (0.5m) from any nearest pump/dispenser. 

 

 

Figure  3-1  Islander PLUS– Installation Control Drawing   

 

3-3. HOME BASE STATION - OVERVIEW 

3-3.1.  General  

Prior to installation, you are required to obtain an overview of the Home Base Station functional 
architecture.  This overview is required in order to draw an architecture diagram with all 
components and their communication links.  

Figure  3-2 shows a functional diagram of the links within the Home Base Station with 4 mechanical 
pumps.  

Figure  3-3 shows a functional diagram of the links within the Home Base Station with 8 mechanical 
pumps.  

 

 

Islander PLUS Manual  

44 

Содержание Islander ICR PLUS



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды