GAS GAS MC50 2021 Скачать руководство пользователя страница 70

Страница: 70 / 119

12 BRAKE SYSTEM

–

Operate the hand brake lever repeatedly until the brake linings are
in contact with the brake disc and there is a pressure point. Secure
the hand brake lever in the activated position.

The brake caliper straightens.

–

Tighten screw

Guideline

Screw, front
brake caliper

M8x60

20 Nm (14.8 lbf ft)

Loctite

243™

–

Tighten screw

Guideline

Screw, front
brake caliper

M8x40

20 Nm (14.8 lbf ft)

Loctite

243™

–

Remove the locking piece of the hand brake lever.

F02998-10

–

Correct the brake fluid level.
Guideline

Brake fluid level below reser-
voir rim

5 mm (0.2 in)

Brake fluid DOT 4 / DOT 5.1 (

p. 108)

–

Position cover

with membrane

–

Mount and tighten screws

Info

Use water to immediately clean up any brake fluid that has
overflowed or spilled.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 37)

12.9

Checking the free travel of the foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

F03002-10

–

Disconnect spring

–

Move the foot brake lever back and forth between the end stop and
the foot brake cylinder piston bracket and check free travel

Guideline

Free travel of foot brake lever

3 … 5 mm (0.12 … 0.2 in)

» If the free travel does not meet specifications:

–

Adjust the free travel of the hand brake lever.

(

p. 69)

–

Attach spring

Содержание MC50 2021
























































































































Результаты поиска

Содержание MC50 2021

Отзывы:

Похожие инструкции для MC50 2021

Бренды по названию

Популярные бренды

GAS GAS MC50 2021, Руководство пользователя

Результаты поиска

Содержание MC50 2021

Отзывы:

Похожие инструкции для MC50 2021

Бренды по названию

Популярные бренды