GAS GAS MC50 2021 Скачать руководство пользователя страница 56

Страница: 56 / 119

11 SERVICE WORK ON THE CHASSIS

11.32

Checking the chain for dirt

400678-01

–

Check the chain for coarse dirt accumulation.
» If the chain is very dirty:

–

Clean the chain. (

p. 54)

11.33

Cleaning the chain

Warning

Danger of accidents

Lubricants on the tires reduces the road grip.

–

Remove lubricants from the tires using a suitable cleaning agent.

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the appli-
cable regulations.

Info

The service life of the chain depends largely on its maintenance.

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 37)

400725-01

Main work

–

Rinse off loose dirt with a soft jet of water.

–

Remove old grease residue with chain cleaner.

Chain cleaner (

p. 110)

–

After drying, apply chain spray.

Off-road chain spray (

p. 110)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 37)

Содержание MC50 2021
























































































































Результаты поиска

Содержание MC50 2021

Отзывы:

Похожие инструкции для MC50 2021

Бренды по названию

Популярные бренды

GAS GAS MC50 2021, Руководство пользователя

Результаты поиска

Содержание MC50 2021

Отзывы:

Похожие инструкции для MC50 2021

Бренды по названию

Популярные бренды