GAS GAS MC 450F 2022 Скачать руководство пользователя страница 90

Страница: 90 / 157

12 BRAKE SYSTEM

A00829-10

–

Position cover

with membrane

. Mount and tighten

screws

Info

Clean up overflowed or spilled brake fluid immediately with
water.

12.6

Checking the front brake linings

Warning

Danger of accidents

Worn-out brake linings reduce the braking effect.

–

Ensure that worn-out brake linings are replaced immediately. (Your authorized GASGAS Motorcycles workshop
will be glad to help.)

A00830-10

(All standard models)

–

Check the brake linings for minimum thickness

Minimum thickness

≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the brake linings of the front brake.

(

p. 88)

–

Check the brake linings for damage and cracking.
» If damage or wear is encountered:

–

Change the brake linings of the front brake.

(

p. 88)

S05118-10

(MC 450F TROY LEE DESIGNS)

–

Check the brake linings for minimum thickness

Minimum thickness

≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the brake linings of the front brake.

(

p. 88)

–

Check the brake linings for damage and cracking.
» If damage or wear is encountered:

–

Change the brake linings of the front brake.

(

p. 88)

12.7

Changing the brake linings of the front brake

Warning

Danger of accidents

Incorrect servicing will cause the brake system to fail.

–

Ensure that service work and repairs are performed professionally. (Your authorized GASGAS Motorcy-
cles workshop will be glad to help.)

Содержание MC 450F 2022






























































































































































Результаты поиска

Содержание MC 450F 2022

Отзывы:

Похожие инструкции для MC 450F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 450F 2022, Руководство пользователя

Результаты поиска

Содержание MC 450F 2022

Отзывы:

Похожие инструкции для MC 450F 2022

Бренды по названию

Популярные бренды