GAS GAS MC 450F 2022 Скачать руководство пользователя страница 60

Страница: 60 / 157

11 SERVICE WORK ON THE CHASSIS

S05133-11

–

Mount and tighten screw

Guideline

Screw, top
steering stem

20 Nm (14.8 lbf ft)

Loctite

243™

S05132-11

–

Using a plastic hammer, tap lightly on the upper triple clamp to
avoid stresses.

–

Tighten screws

Guideline

Screw, top triple
clamp

20 Nm (14.8 lbf ft)

–

Secure the wiring harness with cable holder

on the left.

A00885-12

–

Position the brake caliper. Mount and tighten screws

Guideline

Screw, front
brake caliper

25 Nm (18.4 lbf ft)

Loctite

243™

–

Position the brake line and the clamp. Mount and tighten
screws

Guideline

Screw, brake line
holder

EJOT

1.7 Nm (1.25 lbf ft)

Finishing work

–

Install front fender. (

p. 62)

–

Mount the handlebar cushion.

–

Install the start number plate. (

p. 61)

–

Install the front wheel.

(

p. 99)

–

Check that the wiring harness, throttle cables, and brake and clutch
lines can move freely and are routed correctly.

–

Check the steering head bearing play. (

p. 58)

–

Remove the motorcycle from the lift stand. (

p. 49)

11.13

Checking the steering head bearing play

Warning

Danger of accidents

Incorrect steering head bearing play impairs the handling characteristic and damages com-

ponents.

–

Correct incorrect steering head bearing play immediately. (Your authorized GASGAS Motorcycles workshop will
be glad to help.)

Содержание MC 450F 2022






























































































































































Результаты поиска

Содержание MC 450F 2022

Отзывы:

Бренды по названию

Популярные бренды

GAS GAS MC 450F 2022, Руководство пользователя

Результаты поиска

Содержание MC 450F 2022

Отзывы:

Бренды по названию

Популярные бренды