GAS GAS MC 350F 2022 страница 45 Скачать руководство пользователя

Страница: 45 / 143

TUNING THE CHASSIS 10

10.17

Adjusting the handlebar position

Warning

Danger of accidents

A repaired handlebar poses a safety risk.

If the handlebar is bent or straightened, the material becomes fatigued. The handlebar may break as a result.

–

Change the handlebar if the handlebar is damaged or bent.

Preparatory work

–

Remove the handlebar cushion.

F03177-10

Main work

–

Remove screws

. Take off the handlebar clamps. Remove the

handlebar and lay it to one side.

Info

Cover the components to protect them against damage.

Do not kink the cables and lines.

–

Remove screws

. Take off handlebar supports.

–

Place handlebar supports in required position. Mount and tighten
screws

Guideline

Screw, handlebar
support

M10

40 Nm (29.5 lbf ft)

Loctite

243™

Info

Position the left and right handlebar supports evenly.

–

Position the handlebar.

Info

Make sure the cables and wiring are positioned correctly.

–

Position the handlebar clamps. Mount screws

and tighten

evenly.
Guideline

Screw, handlebar
clamp

20 Nm (14.8 lbf ft)

Info

Make sure the installed gaps are even.

Finishing work

–

Mount the handlebar cushion.

Содержание MC 350F 2022
















































































































































Результаты поиска

Содержание MC 350F 2022

Отзывы:

Похожие инструкции для MC 350F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 350F 2022, Руководство пользователя

Результаты поиска

Содержание MC 350F 2022

Отзывы:

Похожие инструкции для MC 350F 2022

Бренды по названию

Популярные бренды