Garrard 401 Скачать руководство пользователя страница 19

spare parts list

18

Ref.

Garrard

Ref.

Garrard

No.

Part No.

Description of Part

No.

Part No. Description of Part

71898

50 cycle Pulley with Collar and Screws

42501Spring Washers (2)

71899

60 cycle Pulley with Collar and Screws

52493Thrust Pad

21

71761

Turntable Spindle only

31

60542

Lead and Switch Assembly complete

51888

Spring Clip, for Spindle

with Suppressors

22

40151

Screws, for Turntable Spindle Housing

32

53110/02

Earth Lead

(3)

40182Screw

41006

Nuts (3)

41012Nut

42520

Spring Washers (3)

42501Spring Washer

23

71765

Turntable Spindle complete with Hous-

43000Solder Tag

ing

33

71253Top Mounting Plate, with Pillars

40776

Felt Pad

34

71257Bottom Mounting Plate Assembly

40064

Screw for Oil-hole

35

41639Tension Spring, for Bottom Mounting

40858

Plain Washer

Plate

24

44034

Screws for Control Plate (6)

36

40182Screws (3)

25

71254

Speed Change Lever Assembly

42501Spring Washers (3)

26

71900

Brake Pad Lever with Pad

40501

Plain Washers (3)

27

40055

Screws for Brake Pad Lever

37

51834Lifting Cam

40519

Plain Washers (2)

40018Screw

28

41788

Spring Clip

41006Nut

40678

Plain Washer

38

54982

Cover for Voltage Changeover Block

29

41737

Spring Support

39

40443

Stud

40132

Screw

41012Nuts (3)

41061

Nut

42501Spring Washer

42501

Spring Washer

40627Plain Washer

72002

Cable Clip

40

72111Voltage Changeover Block, complete

30

51802

Thrust Plate for Turntable Spindle

with Cover

52075

Gasket

60135Voltage Changeover Block Body

40132

Screws, for Thrust Plate (2)

54926

Wire Links (2)

Содержание 401






















Отзывы: