Garner HD-3WXL Series, Руководство по эксплуатации

Страница: 2 / 6

1 of 5
HD-3WXL SERIES Operation Manual
US
First Pass Second Pass
IMPORTANT SAFETY NOTES
No operator-serviceable parts inside
unit. Maintenance to be done only by
trained personnel.
High Voltage exists inside unit even
when equipment is not under power.
All trouble shooting and wiring checks
must be performed by a qualified
electrician or authorized plant
personnel.
Unplug power cord from the wall to
disconnect power to the system.
Disconnect main power and unplug
unit from the wall before installing
or removing device or servicing
equipment.
PACE MAKER USERS
Due to stray magnetic fields, consult
your physician before operating.
A non-shielded power cord may
be used to connect AC power to
the system. Use only power cords
approved by Garner Products.
For continued protection against risk of
fire, replace fuses with fuses of same
types and ratings only.
Airflow is important. Do not cover
chassis ventilation slots or block
enclosure openings.
Check input voltage selection; if not
compatible with wall voltage, have
technician qualified by Garner Products
modify wiring inside this system before
connecting system plug to wall voltage.
CONTROLS AND INDICATORS
POWER Button (RED) The power button switches the power on and off.
LCD display The LCD display gives status, automatic count, total count, software version, field
strength, user instructions and fault messages.
Media Entrance Door The HD-3WXL media degausser operates automatically when media is
inserted into the media entrance door.
LCD DISPLAY DEGAUSSING INSTRUCTIONS
The following information appears on
the LCD Display from power-up through
one automatic degaussing cycle:
Automatic Degaussing
Step 1: Press POWER button ON
GARNER
PRODUCTS, INC.
Displays manufacturer.
Displays degausser model.
FIRMWARE VER
##
Displays current firmware version.
TOTAL
# −− ##
Displays total erasing cycles. Number on left indicates
number of times the counter reached 50,000.
Insert Media
Session = 0
Ready for media to be placed in the media entrance
door. Counter for erase cycles completed since power
up.
Indicates media entrance door is open – this is normal
when inserting media to be erased.
Step 2: Insert media
Erase Cycle
Initiated
Door has closed and the erase cycle has started.
Charging
>>>>>>>>>>>>>>>>
Displays capacitor charging status.
--------------===|==
Visual indicator of erasing field strength.
Data Eliminated
Indicates power and erasing field strength was verified
good and data has been eliminated.
Step 3: Remove Media
Media gate has lowered and erased media will slide
out.
INITIATION
I ntroduction
The Garner HD-3WXL degausser is a conti nuous duty
capacitive discharge degausser. The unit is designed to
erase hard drives and tape cartridges that fit within the
opening of the Media Entrance Door. The convenient
media loading design accommodates many different types
and sizes of media, without the need for adapters.
Each erase cycle is measured and verified by internal
diagnostics thus eliminating the possibil ity of a non-
erasure. For security purposes, if an insufficient field is
detected, the HD-3WXL will not release the media.
Inspection
Inspect the degausser for shipping damage as soon as
it is unpacked. If the degausser or any accessories are
damaged or fail to operate correctly, notify carrier and
contact your dealer immediately
INSTALLATION
Power Plug
Plug the IEC connector attached to the supplied power cord
into the receptacle on the back of the unit.
Location
The degausser must be placed on a flat, hard surface.
Keep at least a 15 cm (6 inch) distance from any object
that may interfere with the coo ling fan exhaust located on
the backside of the degausser. As a general rule, media
not inten ding to be erased should be kept about 60 cm
(2 ft) away.
Cooling
Forced air-cooling is used to maintain safe ope rating
temperatures within the degausser. The air intake is
located on the back panel and the exhaust is through the
holes in the top panel. To ensure proper cooling, do not
block the air-intake and maintain at least a 15 cm (6 in.)
distance from the back of the degausser to any obstacle.
DEGAUSSING INSTRUCTIONS FOR DLT MEDIA
Remove the plastic protective cases.
Although the data is completely degaussed in one
operation, a second pass rotated at 90 degrees is required
to smooth out any magnetic fluctuation.
Note: If the second pass is not completed, the tape
drive may eject the tape from the tape drive and
indicate that the tape needs cleaning. The second pass
at 90 degrees will correct this condition. If you have
any questions, please contact your dealer.