background image

Error and Warning Messages

Error Message

Cause

Autopilot Action

ECU Voltage is Low

The steering actuator supply voltage has fallen 
below 10 Vdc for longer than 6 seconds.

Continues in normal 
operation

Autopilot is not receiving 
navigation data. Autopilot 
placed in Heading Hold.

The autopilot is no longer receiving valid naviga­
tion data while performing a Route To maneuver.
This message also appears if navigation is 
stopped on a chartplotter before the autopilot is 
disengaged.

Autopilot transitions to 
heading hold

Connection with Autopilot 
Lost

The helm control has lost connection with the 
CCU.

N/A

Low GHC

 Supply Voltage

The supply voltage level has fallen below the 
value specified in the low voltage alarm menu.

N/A

Error: ECU High Voltage

The steering actuator supply voltage has risen 
above 33.5 Vdc

The ECU shuts down

Error: ECU Voltage has 
Dropped Rapidly

The ECU voltage has dropped quickly below 
7.0 Vdc.

The error is cleared when 
the ECU voltage rises 
above 7.3 Vdc.

Error: ECU High Temperature

The ECU temperature has risen above 100°C 
(212°F ).

The ECU shuts down

Error: Lost Communication 
Between ECU and CCU (when 
the autopilot is engaged)

Communication between the CCU and the ECU 
has timed out.

The helm control or chart­
plotter beeps, and the 
autopilot transitions to 
standby.

Contacting Garmin Support

• Go to 

support.garmin.com

 for help and information, such as product manuals, frequently asked questions, 

videos, and customer support.

• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.

© 2019 Garmin Ltd. or its subsidiaries
Garmin

®

 and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Reactor

 is a trademark of Garmin Ltd. or its 

subsidiaries. This trademark may not be used without the express permission of Garmin.
Honda

®

 is a registered trademark of Honda Motor Co., Ltd. and its subsidiaries and affiliates. LOCTITE

®

 is a trademark of Henkel Corporation in the U.S. and elsewhere. 

Mercury

®

 is a trademark of Brunswick Corporation. NMEA

®

, NMEA 2000

®

, and the NMEA 2000 logo are trademarks of the National Marine Electronics Association. 

Yamaha

®

 is a trademark of the Yamaha Motor Corporation. 

© 2019 Garmin Ltd. or its subsidiaries

support.garmin.com

Содержание Reactor 40 Kicker





























Отзывы: