background image

Specifications

Panoptix LiveScope LVS32 Specifications

Dimensions (L x H x W)

136.4 x 96.5 x 44.5 mm (5.37 x 3.8 x 1.75 in.)

Weight (transducer only)

850 g (1.87 lb.)

Frequencies

From 530 to 1.1 MHz

Operating temperature

From 0 to 40°C (from 32 to 104°F)

Storage temperature

From -40 to 85°C (from -40 to 185°F)

Maximum depth/distance

1

61 m (200 ft.)

Field of view

Front to back: 135 degrees
Side-to-side: 20 degrees

Panoptix LiveScope GLS 10 Sonar Module Specifications

Dimensions (W x H x D)

245 x 149 x 65 mm (9.7 x 5.9 x 2.6 in.)

Weight

1.96 kg (4.33 lbs.)

Operating temperature

From -15 to 70°C (from 5 to 158°F)

Storage temperature

From -40 to 85°C (from -40 to 185°F)

Power input

From 10 to 32 Vdc

Power usage

21 W typical, 24 mW min., 58 W max.

Compass-safe distance

178 mm (7 in.)

Data output

Garmin Marine Network

Open-Source Software License

To view the open-source software license(s) used in this product, go to 

developer.garmin.com/open-source

/linux/

.

Cleaning the Transducer

Aquatic fouling accumulates quickly and can reduce your device's performance.
Remove the fouling with a soft cloth and mild detergent.
Wipe the device dry.

© 2018 Garmin Ltd. or its subsidiaries
Garmin

®

, ActiveCaptain

®

, and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. LiveScope

 and Panoptix

 are 

trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.
Android

 is a trademark of Google Inc. Apple

®

 and Mac

®

 are trademarks of Apple Inc., registered in the U.S. and other countries. Wi

Fi

®

 is a registered trademark of Wi-Fi 

Alliance Corporation. Windows

®

 is a registered trademark of Microsoft Corporation in the United States and other countries. Other trademarks and trade names are those 

of their respective owners.

Dependent upon water salinity, bottom type, and other water conditions.

13

Содержание PANOPTIX LIVESCOPE LVS32















Отзывы:

Похожие инструкции для PANOPTIX LIVESCOPE LVS32