background image

 

Page 4-6 

GTN 625/635/650 TSO Installation Manual 

Rev. C 

190-01004-02 

4.9 

Coaxial Cable Installation 

Follow the steps below for installation of the coaxial cables: 

1.

 

Route the coaxial cable to the radio rack location keeping in mind the recommendations of 
Section 3.4. Secure the cable in accordance with AC 43.13-1B Chapter 11, section 11.  

2.

 

Trim the coaxial cable to the desired length and install the TNC and BNC connectors per the 
cabling instructions on Figure 4-1 below.  If the connector is provided by the installer, follow the 
connector manufacturer‘s instructions for cable preparation. 

 

GASKET

NUT

9

16

3

16

1.  PLACE NUT AND GASKET OVER CABLE AND STRIP JACKET
    TO DIMENSION SHOWN.

2.  COMB OUT BRAID AND TRIM DIELECTRIC TO
     DIMENSION SHOWN.

3.  PULL BRAID WIRES FORWARD AND TAPER TOWARD CENTER
     CONDUCTOR. PLACE CLAMP OVER BRAID AND PUSH BACK
     AGAINST JACKET.

4.  FOLD BACK BRAID OVER CLAMP AS SHOWN. TRIM OFF
     EXCESS BRAID. SOLDER CONTACT TO CENTER CONDUCTOR.

5.  INSERT CABLE CLAMP AND GASKET INTO CONNECTOR
     BODY MAKING SURE THAT SHARP EDGE OF CLAMP SEATS
     PROPERLY AND TIGHTEN NUT.

 

Figure 4-1.  Coaxial Cable Installation 

Содержание GTN 635





































































































































































































Отзывы: