background image

6

I

NSTALLATION

 I

NSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

Radar

ABOVE - BEST

BELOW - OK

EMI

SS JAYHAW

K

GOOD

BETTER

BEST

3'

VHF Radio Antenna

Radar

EMI (Electromagnetic Interference) 

from engine components

Signal Interference

 

 

NOTE: 

Mount the antenna at least 3 ft away from 

(preferably above) the path of any radar beam or a 

VHF radio antenna. 

Bottom of GPS 17 

Mounting holes

Installing the GPS 17

The GPS 17 can be flush mounted or installed on any standard 1" O.D. (Outer 

Dimension), 14 threads-per-inch marine mount. When mounting the GPS 17, the 

cable can be run externally or through the mounting panel or through the center of 

the marine mount. 
The GPS 17 connects to the 18-pin Power/Data Cable on the GPSMAP 

2006C/2010C and provides the GPS/WAAS signal for the unit. If two or more 

GPSMAP 2006C/2010C units are installed, only one GPS 17 needs to be installed.
To ensure the best reception, mount the GPS 17 in a location that has a clear, 

unobstructed view of the sky in all directions. Avoid mounting the GPS 17 where 

it is shaded by the boat’s superstructure, a radome antenna, or mast. Sailboat 

users should avoid mounting the unit high on the mast to prevent inaccurate 

speed readings caused by excessive heeling. The unit provides more stable 

readings if it is located nearer to water level. 

Mount the GPS 17 at least 3 ft 

away from (preferably above) the path of any radar beam or a VHF radio 

antenna.

 Temporarily secure the unit in the desired mounting location and test for 

correct operation. With correct operation verified, permanently mount the unit. If 

interference with other electronics is experienced, try a different location.

 

NOTE: 

Never paint the GPS 17 or clean it with harsh solvents.

To flush mount the GPS 17:

1.  Cut out the Mounting Template provided on page 11, and tape it on the selected mounting location.
2.  Mark the center of each mounting hole by tapping the end of a center punch or pointed object with a hammer. If the cable is going to be 

installed through the mounting panel, mark the center of the additional hole.

3.  Drill the holes using the appropriate drill bit(s).
4.  Align the GPS 17 over the mounting holes and fasten using M4 screws. The mounting threads in the GPS 17 are 8.10 mm deep. Do not 

use screws that thread into the GPS 17 deeper than 8 mm, or the case may be damaged.

 

The GPS 17 can be installed with the coax through the panel 

or on the outside of the unit. If the coax is run through the 

panel, seal the outside exit area with marine sealant.

Содержание GPSMAP 17













Отзывы: