Garmin GMA 342 Скачать руководство пользователя

Страница: 33 / 65

190-01878-02

GMA 342/345 Installation Manual

Rev. 5

Page 3-2

NOTE

1. Non-Garmin part numbers shown are not maintained by Garmin and consequently are subject to

change without notice.

2. Extracting #18 and #20 contacts requires that the expanded wire barrel be cut off from the contact.

It may also be necessary to push the pin out from the face of the connector when using an extractor

due to the absence of the wire. A new contact must be used when reassembling the connector.

3.3 Antenna Installation

Install the antenna according to the antenna manufacturer’s instructions.

3.3.1 Antenna Cable Connectors

The antenna cable requires a BNC plug connector. Follow BNC connector manufacturer instructions for

assembly of the BNC connector.

3.4 Shield Block Backshell Installation Instructions

3.4.1 Backshell Installation Parts

The GMA 342/345 connector kit includes two Garmin backshell assemblies. Garmin’s backshell

connectors give the installer the ability to quickly and easily terminate shield grounds at the backshell

housing using the Shield Block. To assemble the backshell connectors and grounding system, refer to

instructions provided in the Shield Block Installation Instructions (190-00313-09).

Table 3-2 Recommended Crimp Tools

Manufacturer

Hand

Crimping

Tool

18-20 AWG

22-28 AWG

Positioner

Insertion/

Extraction

Tool (Note 2)

Positioner

Insertion/

Extraction

Tool

Military P/N

M22520/2-01

N/A

M81969/1-04

M22520/2-09

M81969/1-04

Positronic

9507

9502-11

M81969/1-04

9502-3

M81969/1-04

AMP

601966-1

N/A

91067-1

601966-6

91067-1

Daniels

AFM8

K774

M81969/1-04

K42

M81969/1-04

Astro

615717

N/A

M81969/1-04

615725

M81969/1-04

Содержание GMA 342


































































Результаты поиска

Содержание GMA 342

Отзывы:

Похожие инструкции для GMA 342

Бренды по названию

Популярные бренды

Garmin GMA 342, Руководство по установке

Результаты поиска

Содержание GMA 342

Отзывы:

Похожие инструкции для GMA 342

Бренды по названию

Популярные бренды