Garmin GDL 82 Скачать руководство пользователя страница 37

Страница: 37 / 68

Connector Pinouts

190-01810-00

GDL 82 TSO Installation Manual

Rev. 5

Page 5-5

5.2.4 Discrete Output

This output is an open drain capable of sinking 500 mA when active/grounded.

Table 5-6 Discrete Outputs

Fault Alert

The Fault Alert functions as an equipment annunciator output.

Table 5-7 Fault Alert Functions

5.2.5 Time Mark Inputs

Table 5-8 Time Mark Inputs

The GDL 82 accepts a Time Mark Input signal pair. When used with an external position source, the navigator sense
Time Mark signals connect to the Time Mark input pins. Connect a single-ended time mark to TIME MARK A.

PIN NAME

CONNECTOR

I/O

FAULT ALERT

P821

Out

FAULT ALERT

MEANING

ANNUNCIATOR LAMP

Active (grounded - 0 V)

System is not transmitting all FAA required
ADS-B data.

Inactive (open)

ADS-B Out messages provide all required
information.

Off

PIN NAME

CONNECTOR

I/O

TIME MARK A

P821

TIME MARK B

P821

Содержание GDL 82





































































Результаты поиска

Содержание GDL 82

Отзывы:

Похожие инструкции для GDL 82

Бренды по названию

Популярные бренды

Garmin GDL 82, Руководство по установке

Результаты поиска

Содержание GDL 82

Отзывы:

Похожие инструкции для GDL 82

Бренды по названию

Популярные бренды