Garmin Fusion Apollo MS-AP41200 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 22

Garmin Fusion Apollo MS-AP41200 Скачать руководство пользователя страница 21

Potential Cause

Potential Resolution

DSP setting or
volume issue

Check the DSP settings in the Fusion-Link app and make sure the correct amplifier,
speakers, and/or subwoofer(s) are selected.
NOTE: You must select the option in the app to send the DSP settings to the stereo after
you configure the settings.

Speaker fault

Check all connected speaker wires.
• Make sure the speaker wires are connected to the speaker terminal blocks and to the

speakers properly.

• Make sure there are no shorts in the speaker wires, and that there are no cuts in the

speaker-wire jackets that may result in a short.

Internal amplifier
or power supply
fault

Disconnect the amplifier from the power source for one minute, then reconnect it and
test for proper operation. If the LED continues to show a red fault, contact support.

物質宣言

部件名称

有毒有害物质或元素

铅

汞

镉

六价铬

多溴联苯

多溴二苯醚

电路版

框体

附件

本表格依据

SJ/T11364

的规定编制。

:

代表此种部件的所有均质材料中所含的该种有害物质均低于

(GB/T26572)

规定的限量

:

代表此种部件所用的均质材料中

,

至少有一类材料其所含的有害物质高于

(GB/T26572)

规定的限量

*

该产品说明书应提供在环保使用期限和特殊标记的部分详细讲解产品的担保使用条件。

产品

Fusion Apollo Multichannel Amplifiers Installation Instructions Installation Instructions

21

«
...
19
20
21
22
»

Содержание Fusion Apollo MS-AP41200























Отзывы:

Нет отзывов