1. Some routes may require manual navigation by
the pilot between waypoints. These points will
be noted in the Flight Plan page as “Pilot Nav.”
2. Active guidance is not provided to the pilot.
Follow procedural directions.
3. Once the Pilot Nav Leg is completed, press the
key to sequence to the next leg in your
flight plan.
SUSP
Navigating a Pilot Nav Leg
If the holding pattern is in the database for the
destination waypoint of your flight plan,
follow the automatic guidance on the unit display.
Navigating a Holding Pattern
Holding Pattern is in the database
1. Press
(
).
2. Turn the
knob to highlight the desired
waypoint to perform the holding pattern.
3. Press the
key.
4. Use the
and
knobs to select
Right or Left turn, Course, and hold leg time
or length.
5. Press
.
6. When you reach the holding pattern, flight plan
sequencing is suspended (SUSP will appear)
automatically. Roll steering guidance is
available.
7. Press
to exit the hold pattern and to
return to the flight plan, or press
or
to exit holding pattern.
DIRECT-TO D->
Large
Hold
Large
Small
Menu/Enter
SUSP
D->
FlyLeg
Holding Pattern Inserted While On Route
Course To operation allows you to add an intercept
course to the selected waypoint. Upon reaching
the selected waypoint, the flightplan will sequence
to the next waypoint in the flightplan normally.
1. Press
.
a. Press
and turn the
knob to
select a waypoint in your flight plan.
b. Press
and select a new waypoint, if
desired, with the
and
knobs.
2. Press
(you may have to press
first).
3. Change the course bearing, if desired. Use the
and
knobs to change the course
value.
4. Press
.
Direct-To
WPTS
Large
or
DB
Large
Small
CrsTo
More
Large
Small
Menu/Enter
Direct-To - Intercept Course To Wpt
The Course From operation allows you to
navigate from a waypoint on a selected
course. When the Course From operation is
executed, the CDI will indicate FROM and the
flightplan will go into suspend mode (SUSP);
it will not automatically sequence the
flightplan waypoints.The airplane will track
outbound on the selected radial until instructed
otherwise.
1. Press
. Select a new waypoint,
if desired, with the
and
knobs.
2. Press
.
3. Change the course bearing, if desired.
Turn the
knob to change the 10s
value. Turn the
knob to change the
1s value.
4. Press
.
Direct-To
Large
Small
CrsFr
Large
Small
Menu/Enter
(you may have to press
first)
More
Direct-To - Intercept Course From Wpt
With the FlyLeg Menu selection you can
activate a particular leg of your flight plan. If
you have picked an invalid leg a message will
appear to warn you.
1. Press
. Press the
smart key
if necessary.
2. Select the desired leg of your flight plan with
the
knob.
3. Press the
key to activate the
selected leg.
Direct-To
WPTS
Large
FlyLeg
Direct-To - FlyLeg
When the OBS mode is active, use the CDI/HSI
control to set an intercept course to any
waypoint as you would with a radial for a VOR.
1. Press
. Select a new waypoint, if
desired, with the
and
knobs,
otherwise the destination waypoint is used.
2. Press
. Now use the external CDI/HSI
resolver to control the selected course.
Direct-To
Large
Small
OBS
Direct-To - OBS
1. Press
and then the
smart key.
2. Turn the
knob or press the
or
smart keys to switch between Old or New
messages.
3. Turn the
knob to view the available
messages.
FN
MSG
Large
New
Old
Small
Messages (MSG)