Garmin ECHOMAP Ultra 122sv, Руководство пользователя

Страница: 35 / 52

Speed indicator.
Increases the speed.
Enables the cruise control at the current speed over ground
(SOG).
Engages the propellor at full speed.
Trolling motor status.
Enables anchor lock, which uses the trolling motor to hold your
position.
Steers the trolling motor.
When in anchor lock, jogs the anchor lock position forward,
backward, left, or right.
Enables heading hold (set and maintain the current heading).
When the trolling motor is in heading hold, an autopilot bar
appears in the trolling motor bar.
Opens the trolling motor settings.
Trolling Motor Settings
From the trolling motor bar, select .
Calibrate : Calibrates the trolling motor compass ( Calibrating the
Trolling Motor Compass , page 29 ) and sets the trolling
motor bow offset ( Setting the Bow Offset , page 29 ).
Anchor Gain : Sets the response of the trolling motor when in
anchor lock mode. If you need the trolling motor to be more
responsive and move quicker, increase the value. If the
motor is moving too much, decrease the value.
Navigation Gain : Sets the response of the trolling motor when
navigating. If you need the trolling motor to be more
responsive and move quicker, increase the value. If the
motor is moving too much, decrease the value.
Heading Hold Mode : Sets the heading hold mode. The Vessel
Align option attempts to keep the boat pointing in the same
direction. The Navigate To option attempts to navigate a
straight line in the requested direction.
Auto Power On : Turns on the trolling motor when you apply
power to the system.
Prop. Stow Side : Sets which side of the trolling motor the
propellor rotates to when stowing the trolling motor. This is
helpful when you store other items near the stowed propellor.
Shortcut Keys : Enables the shortcut keys on the trolling motor
remote control to work with this particular chartplotter. The
keys work with only one chartplotter at a time.
Restore Defaults : Resets the trolling motor settings to the
factory default values.
Assigning a Shortcut to the Trolling Motor Remote
Control Shortcut Keys
You can quickly open commonly used screens by assigning a
shortcut key on the trolling motor remote control. You can create
a shortcut to screens, such as sonar screens and charts.
1
Open a screen.
2
Hold a shortcut key.
TIP: The shortcut is also saved to the Frequently Used
category with the shortcut key number.
Calibrating the Trolling Motor Compass
You must calibrate the compass in the trolling motor before you
can use the autopilot features.
1
Drive the boat to an open area of calm water.
2 From the trolling motor bar, select > Calibrate >
Compass Cal. .
3
Follow the on-screen instructions.
Setting the Bow Offset
Based on the installation angle, the trolling motor may not align
with the center line of your boat. For the best results, you should
set the bow offset.
1
Adjust the angle of the trolling motor so it aligns with the
center line of your boat , pointing straight forward.
2
From the trolling motor bar, select > Calibrate > Bow
Offset .
Gauges and Graphs
The gauges and graphs provide various information about the
engine and environment. To view the information, a compatible
transducer or sensor must be connected to the network.
Viewing the Compass
You can view information about your bearing, heading, and
route using the compass.
Select Gauges > Compass .
Viewing Trip Gauges
Trip gauges show information for odometer, speed, time, and
fuel for your present trip.
Select Gauges > Trip .
Resetting Trip Gauges
1
Select Gauges > Trip > Menu .
2
Select an option:
• To set all the readings for the present trip to zero, select
Reset Trip .
• To set the maximum speed reading to zero, select Reset
Maximum Speed .
• To set the odometer reading to zero, select Reset
Odometer .
• To set all the readings to zero, select Reset All .
Viewing Engine and Fuel Gauges
Before you can view engine and fuel gauges, you must be
connected to a NMEA 2000 network capable of sensing engine
and fuel data. See the installation instructions for details.
Select Gauges > Engine .
Gauges and Graphs 29