Garmin Echomap Plus 40 series, Руководство пользователя

Страница: 42 / 50

Calibrating a Water Speed Device
If you have a speed-sensing transducer connected to the
chartplotter, you can calibrate that speed-sensing device to
improve the accuracy of water-speed data displayed by the
chartplotter.
1
Select Settings > My Vessel > Calibrate Water Speed .
2
Follow the on-screen instructions.
If the boat is not moving fast enough or the speed sensor is
not registering a speed, a message appears.
3
Select OK , and safely increase the boat speed.
4 If the message appears again, stop the boat, and ensure the
speed-sensor wheel is not stuck.
5
If the wheel turns freely, check the cable connections.
6
If you continue to get the message, contact Garmin product
support.
Setting the Fuel Capacity of the Vessel
1
Select Settings > My Vessel > Fuel Capacity .
2
Enter the combined total capacity of the fuel tanks.
Synchronizing the Fuel Data with the Actual Vessel
Fuel
You can synchronize the fuel levels in the chartplotter with the
actual fuel in the vessel when you add fuel to your vessel.
1
Select Gauges > Engine > MENU .
2
Select an option:
• After you have filled up all the fuel tanks on the vessel,
select Fill Up All Tanks . The fuel level is reset to
maximum capacity.
• After you have added less than a full tank of fuel, select
Add Fuel to Boat , and enter the amount added.
• To specify the total fuel in the vessel tanks, select Set
Total Fuel Onboard , and enter the total amount of fuel in
the tanks.
Customizing Engine Gauge and Fuel Gauge Limits
You can configure the upper and lower limits and the range of
desired standard operation of a gauge.
NOTE: Not all options are available for all gauges.
1 From an applicable gauges screen, select MENU > Gauge
Setup > Set Gauge Limits .
2
Select a gauge to customize.
3
Select Gauge Limits > Custom .
4
Select an option:
• To set the minimum value of the standard operating
range, select Rated Min. .
• To set the maximum value of the standard operating
range, select Rated Max. .
• To set the lower limit of the gauge lower than the rated
minimum, select Scale Min. .
• To set the upper limit of the gauge higher than the rated
maximum, select Scale Max. .
5
Select the limit value.
6
Repeat steps 4 and 5 to set additional gauge limits.
Communications Settings
NOTE: Some settings and options require additional charts or
hardware.
Select
Settings > Communications .
Serial Port : Sets the input/output format for the serial port to
use when connecting the chartplotter to external NMEA
devices, computers, or other Garmin devices.
NMEA 0183 Setup : Sets the NMEA 0183 sentences the
chartplotter transmits, how many digits to the right of the
decimal point are transmitted in a NMEA output, and how
waypoints are identified ( NMEA 0183 Settings , page 36 ).
NMEA 2000 Setup : Allows you to view and label the devices on
the NMEA 2000 network ( NMEA 2000 Settings , page 36 ).
Marine Network : Allows you to view the devices with which you
are sharing maps, sonar, or radar. Not available on all
chartplotter models.
NOTE: You can only view networked data on a model that
supports that data. For example, you cannot view networked
radar on model that does not support radar.
Wi-Fi Network : Allows you set up the Wi
‑
Fi network ( Setting Up
the Wi
‑
Fi Wireless Network , page 37 ).
NMEA 0183
The chartplotters support the NMEA 0183 standard, which is
used to connect various NMEA 0183 devices, such as VHF
radios, NMEA instruments, autopilots, wind sensors, and
heading sensors.
To connect the chartplotter to optional NMEA 0183 devices, see
the chartplotter installation instructions.
The approved NMEA 0183 sentences for the chartplotter are
GPAPB, GPBOD, GPBWC, GPGGA, GPGLL, GPGSA, GPGSV,
GPRMB, GPRMC, GPRTE, GPVTG, GPWPL, GPXTE, and
Garmin proprietary sentences PGRME, PGRMM, and PGRMZ.
This chartplotter also includes support for the WPL sentence,
DSC, and sonar NMEA 0183 input with support for the DPT
(depth) or DBT, MTW (water temperature), and VHW (water
temperature, speed, and heading) sentences.
NMEA 0183 Settings
Select Settings > Communications > NMEA 0183 Setup .
Sounder : Enables NMEA 0183 output sentences for the
sounder (if applicable).
Route : Enables NMEA 0183 output sentences for routes.
System : Enables NMEA 0183 output sentences for system
information.
Garmin : Enables NMEA 0183 output sentences for Garmin
proprietary sentences.
Posn Precision : Adjusts the number of digits to the right of the
decimal point for transmission of NMEA output.
Waypoint IDs : Sets the device to transmit waypoint names or
numbers via NMEA 0183 while navigating. Using numbers
may resolve compatibility issues with older NMEA 0183
autopilots.
Diagnostics : Displays NMEA 0183 diagnostic information.
Defaults : Restores the NMEA 0183 settings to the original
factory defaults.
NMEA 2000 Settings
Select Settings > Communications > NMEA 2000 Setup .
Device List : Displays the devices connected to the network.
Label Devices : Changes the labels for available connected
devices.
Naming Devices and Sensors on the Network
You can name devices and sensors connected to the Garmin
Marine Network and the NMEA 2000 network.
1
Select Settings > Communications .
2
Select Marine Network or NMEA 2000 Setup > Device List .
3
Select a device from the list on the left.
4
Select Change Name .
5
Enter the name, and select Done .
36 Device Configuration