background image

Part # 4521353 (06/17/09)

Page 19

FAULT FINDING

If servicing is required, we suggest that servicing be performed by your local authorized service agency or other competent 

persons, according to the law. 

Sealed Hotplates Diagnostics

PROBLEM

POSSIBLE CAUSE

SOLUTION

Water in pot does not boil 

or water takes too long 

to boil; with switch set to 

position “6”.

Pot has irregular bottom.

Use a flat bottom pot.

Pot too large for element size.

Use a smaller diameter pot

Pot too small for element size.

Use a larger diameter pot.

Element was preheated before  pot was 

placed on elements.

Allow element to cool protector. Protector 

will reset.

One element circuit may be defective.

Replace heating element.

Six heat switch my be defective.

Replace six heat switch.

Tubular Hotplates Diagnostics

PROBLEM

POSSIBLE CAUSE

SOLUTION

Hotplate too hot or cold.

Defective infinite switch.

Replace indefinite switch.

Hotplate not heating at all

Defective heating element.

Replace element.

Defective infinite switch.

Replace indefinite switch.

Fryer Diagnostics

PROBLEM

POSSIBLE CAUSE

SOLUTION

Power indicator is on. 

Heating indicator comes 

on. Fryer is not recovering 

or heating evenly.

One or more elements are defective.

Replace element.

Sensor is defective.

Replace sensor.

Thermostat is defective. 

Replace thermostat.

A contactor is defective. 

Replace contactor. 

Red indicator light is on. 

Fryer is not heating.

High temperature limit has been tripped. 

Lift the elements and reset the limit red 

button, the lower elements into fry tank. 

Thermostat may be defective.

Replace thermostat.

Contactor my be defective. 

Replace contactor. 

HI Limit may be defective.

Replace hi limit.

Power indicator is on. 

Heating indicator is off. 

Fryer is not heating. Red 

indicator is off. 

Sensor circuit open.

Check sensor connection/replace sensor.

Thermostat may be defective.

Replace thermostat.

Sensor my be defective.

Replace sensor.

Short circuit in sensor connection.

Check sensor connection/replace sensor.

Содержание EDU-15B

























Отзывы: