background image

Part # 4520498 (01/08)

Page 4

DIMENSIONS AND SPECIFICATIONS

INSTALLATION

IMPORTANT: 

The installation must comply with local codes, 

or in the absence of local codes, with  

CAN/CSA - B149 Installation Code – latest edition or with the 

National Fuel Gas Code NFPA 54 ANSI Z22 .1 – latest edition . 

All burner adjustments and settings shall be made by a 

qualified gas technician . 

Serial Plate Location

All burner inputs are shown on the Serial/Rating Plate of 

each unit, located on the bottom of the control section near 

the front .

When corresponding with the factory or your local 

authorized factory service center regarding service problems 

or replacement parts, be sure to refer to the particular unit 

by the correct model number (including the prefix and suffix 

letters and numbers) and the warranty serial number . The 

rating plate contains this information .

INSTALLATION NOTES

MINIMUM SUPPLY PRESSURE REQUIRED

ELECTRICAL CHARACTERISTICS

Combustible Wall Clearances

Natural 

Propane

Specifications

Sides

Back

7" W .C . (17 .4mbar)

11" W .C . (27 .4mbar)

120 V, Single Phase, 60Hz, 1 amp 

6' (1829mm)  

power supply cord provided

MANIFOLD PRESSURE REQUIRED,  

AFTER BUILT-IN  REGULATOR

6" (152mm)

6" (152mm)

 .5” W .C . (8 .75 mbar)

10” W .C . (25mbar)

 IMPORTANT: Unit must be 

installed on legs for proper 

air circulation . A minimum 4” 

(101mm) air space must be 

maintained below unit for 

required air flow to burners .

 Gas Input Ratings shown are for 

installations up to 2,000 feet (610mm) 

above sea level . BTU input ratings must 

be derated for high altitude installations

 NOTE: No cord and plug on export 

units .  Direct connection to junction 

box .

VENTILATION

EXPORT VOLTAGES

• Commercial cooking equipment 

requires an adequate ventilation system . 

Foradditional information, refer to the 

National Fire Protection Association’s 

Standard NFPA 96 . 

• NOTE: Export voltages are available 

on request .

ENTRY CLEARANCE

Crated

Uncrated

• 220-240 volt, 50 Hz, 0 .4 amps, single 

phase .

40" (1016mm)

8" (965mm)

INPUT CHART - Natural Or Propane Gas

Model 

Number

BTU/ 

HOUR

Kw

Gas 

Inlet

Shipping Weight

LBS .

KGS .

CG-48F

120,000

5 .00

/4"

625

284

CG-60F

150,000

44 .00

/4"

765

48

CG-72F

180,000

52 .70

1"

905

411

Содержание CG-48F













Отзывы: