background image

5

 

 

Section  2:  INSTALLATION

 

 

2.1

 

Introduction

 

 

This manual has been compiled not only for the care and maintenance of the Welch Dry Vacuum pump now in 
your possession, but as a helpful reference and guide to prevent many problems which can occur if used 
improperly.

 

 

2.2

 

Unpacking

 

 

Carefully remove the Dry Vacuum pump from the shipping case and unfasten and remove the wooden skid. 
Preserve all paperwork for future reference.  If damage has occurred from shipment a claim must be filed with the 
carrier immediately; preserve the shipping carton for inspection by the carrier.  If you are required to 
communicate with your dealer or Welch Vacuum be sure to include your order numbers for quick identification. 
Do not return the pump to the factory without first calling for a returned goods number.

 

 

2.3

 

Pump Mounting

 

 

Rubber feet are attached to the pump.  Rubber feet are excellent for applications involving a semi-flexible surface 
such as bench tops; they help to isolate noise and eliminate creeping.  T h e   2 0 9 0 / 2 0 8 5 vacuum pumps should 
be mounted in a horizontal plane.

 

 

2.4

 

Pump Location

 

 

The pressure/vacuum pump should be located preferably in a clean, dry and well ventilated area. Please be sure 
not to block the ventilation ports located on the motor housing. The pump should be placed where the surrounding 
temperature remains between 10oC and 40oC (50oF and 104oF). Always check to insure the location chose is 
protected from direct or indirect moisture contact.   Welch recommends that the pump be installed at the highest 
point within the system to prevent possible water condensate from entering the pump.  The pump should be 
located as closely to its system in order to utilize it most efficiently.

 

 

 

 

 

   

 

2.5

 

Intake and Discharge Provisions

 

 

The intake/exhaust connections are NW25 ISO vacuum flange with a 3/8"-18 NPT threaded I.D. 

 

 

 

 

WARNING

 

The motor is thermally protected and will automatically restart 

unexpectedly when the overload device resets.

 

WARNING

 

Bursting Hazard 

 Parts for use on exhaust port should be suitable 

for pressures not less than 100 PSIG

.

 

Содержание Welch 2090W-01

















Отзывы: