background image

21

www.gd-elmorietschle.com

 © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH

 

|

Maintenance and repair

H

M

K

I

7.2.1  Changing the oil

Fig. 4   Changing the oil

H

 

Oil filling point with vent screw

I

 

Oil sight glass

K

 

Oil discharge point

M

 

Oil recommendation plate

NOTICE

Always change the oil when the machine is at 
operating temperature and in an atmospherically 
ventilated area.
If it is not completely emptied the amount that can 
be refilled is reduced.

The waste oil must be disposed of in compliance with 
the local environmental protection regulations.
If you are going to use another oil type, empty the oil 
removing device housing and oil cooler completely.
A minimum oil quantity can get out of the vent screw 
due to pressure compensation. If larger quantities of 
oil escape, wash the internal filter of the vent screw.

The oil level in the sight glasses (Fig. 4/I) must be 
checked every month.
The machine must be switched off and vented to at-
mospheric pressure to top up the oil.With clean op-
erations the oil must be changed after every 20,000 
operating hours.
The oil viscosity must comply with ISO VG 150 as 
per DIN 51519.
Designation as per DIN 51502: CLP HC 150.

We recommend the following oil brand:  

GEAR-

LUBE 150 or equivalent oils by other manufacturers 
(also see oil recommendation plate (Fig. 4/M)).

Содержание Elmo Rietschle C-VLR 301





























Отзывы: