background image

25

9. CLEAN AIR FILTER (Fig. Z1&Z2)

CAUTION: Do not clean filter in gasoline or 
other flammable solvent to avoid creating 

a fire hazard or producing harmful evaporative 
emissions.
Cleaning the air filter:

A dirty air filter decreases the life and performance of 
the engine and increases fuel consumption and harmful 
emissions. Always clean your air filter after 10 tanks 
of fuel or 5 hours of operation, whichever comes first. 
Clean more frequently in dusty conditions. A used air 
filter can never be completely cleaned. It is advisable 
to replace your air filter with a new one after every 50 
hours of operation, or annually, whichever comes first.

10. REPLACE SPARK PLUG
Cylinder fins (Fig. AA1)

Dust clogging between the cylinder fins will cause 
overheating of the engine periodically check and clean 
the cylinder fins after removing the air cleaner and the 
cylinder cover.
When installing the cylinder cover, make sure that 
switch wires and grommets are positioned correctly in 
place.

NOTE:

 Be sure to block the air intake hole.

Spark plug (Fig. AA2)

Clean the electrodes with a wire brush and reset the 
gap to 0.65mm as necessary.
The spark plug should be replaced each year to ensure 
the engine starts easier and runs better. Ignition timing 
is fixed and nonadjustable.
1) Loosen 3 screws on cylinder cover.
2) Remove the cylinder cover.
3) Pull off the spark plug boot.
4) Remove spark plug from cylinder and discard.
5) Replace with a new spark plug and tighten securely 
with a 3/4 inch (19mm) socket wrench. Spark plug gap 
should be 0.025 inch (0, 6 mm).
6) Reinstall the spark plug boot.
7) Reinstall the cylinder cover and 3 screws. Tighten 
securely.

11. REPLACE FUEL FILTER

To replace fuel filter, drain your unit by running it dry of 
fuel. Remove fuel cap and its connected retainer from 
tank. Pull filter from tank and remove from line. Replace 
and reassemble.

12. CHAIN ADJUSTMENT

See 

CHAIN TENSION

 in ASSEMBLY section.

Fi

g. P2

Fi

g. Z1

Fi

g. Z1

Fi

g. AA1

Fig.Z1

Fi

g. P2

Fi

g. Z1

Fi

g. Z1

Fi

g. AA1

Fig.AA1

Fig.AA2

Fi

g. P2

Fi

g. Z1

Fi

g. Z1

Fi

g. AA1

Fig.Z2

Содержание GM45CS3

































Отзывы: