background image

Winding the line

Should you wish to wind the line yourself, the instructions are 
provided below. Self-winding, however, is NOT recommended 
because if the line is not wound properly it can cause the 
trimmer’s feed system to malfunction. For this reason, users are 
strongly urged to purchase the pre-wound spool.

1.   The spool can hold 6 mof line. Remove the white cover. 

Holding the loose ends of the line together with one hand, 
find the center of the line with the other hand and hook this 
center loop into the groove on the spool as shown in Fig 21.

2.   Wind the line following the directional arrows on the spool 

housing and hook the two ends into the side grooves (Fig 22).

Repair

This product does not contain any parts that can be repaired by 
the consumer. Contact an authorised service centre or a similarly 
qualified person to have it checked and repaired.

Power cord

If the supply cord is damaged, it must be replaced by a special cord 
or assembly available from the manufacturer or its service agent.

UK plug

If you need to replace the fitted plug, then follow the instructions
below.
IMPORTANT: The wires in the mains lead are coloured in
accordance with the following code:
Blue – Neutral, Brown – Live
As the colours of the wire in the mains lead of this product
may not correspond with the coloured marking identifying the

24

Fig 21

Fig 22

www.coreservice.co.uk

AFTER SALES SUPPORT

IRE

GB

01904 727501

019022605

MODEL: GLGT400, 04/15, 64887

Содержание GLGT400
































Отзывы: