Gardena Flymo 1200R страница 20 Скачать руководство пользователя

Страница: 20 / 48

See

Indicator lamp in the charging station on page 39 if

the lamp does not indicate a solid or flashing green light.

3.9 First start-up and calibration

When the main switch is set to position

1 for the first

time, a start-up sequence in the robotic lawnmower’s

menu must be carried out as well as an automatic

calibration of the guide signal. The calibration is also a

good test to see that the installation of the guide wire

has been done in such a way that the robotic

lawnmower can easily follow the guide wire from the

charging station.
1. Open the hatch by pressing the STOP button.
2. Set the main switch to position

A start-up sequence begins when the robotic

lawnmower is started for the first time. The following

is requested:
•

Language.

•

Country

•

Current time

•

Date

•

4 digit PIN code. All combinations except 0000

are permitted.

Note: Use the

MEMO page at the beginning of the

manual to make a note of the PIN code.

3. Place the robotic lawnmower in the charging station

as requested in the display. Press the START button

and close the hatch. The robotic lawnmower will now

start the guide calibration, by leaving the charging

station and following the guide wire to the point

where the guide wire is connected to the boundary

wire to begin mowing there. Check that the robotic

lawnmower can follow the guide wire all the way. If it

cannot, this may be due to an incorrectly installed

guide wire. In this case, check that the installation is

performed as described in

Installation of the guide

wire on page 18. Then carry out a new calibration.

See

Calibrate guide, Flymo 1200R on page 24.

3.10 Test docking with the charging station

Before using the robotic lawnmower, check that the

robotic lawnmower can follow the guide wire all the way

to the charging station and easily docks with the

charging station. Perform the test below.
1. Open the panel hatch by pressing the STOP button.
2. Place the robotic lawnmower close to the point

where the guide wire is connected to the boundary

wire. Place the robotic lawnmower about 2 m from

the guide wire, facing the guide wire.

3. Select

HOME mode by pressing the house symbol

key and pressing

OK when the cursor is at Home.

Press START and close the hatch.

4. Check that the robotic lawnmower follows the guide

wire all the way to the charging station and that it

docks with the charging station. The test is approved

only if the robotic lawnmower is able to follow the

guide wire the entire distance to the charging station

and docks at the first attempt. If the robotic

lawnmower is unable to dock on the first attempt, it

will automatically try again. The installation is not

approved if the robotic lawnmower needs two or

more attempts to dock with the charging station. In

this case, check that the charging station, the

boundary wire and the guide wire are installed in

accordance with the instructions.

5. The robotic lawnmower will stay in the charging

station until

AUTO or MAN mode is selected. See

Operation selection on page 30.
The guide system must first be calibrated if the

above test is to provide a satisfactory result. See

First start-up and calibration on page 20.

3.11 Control panel

3.11.1 Instruction - Control panel

All commands and settings for the robotic lawnmower

are made via the control panel. All functions are

accessed via a number of menus.
The control panel consists of a display and a keypad. All

information is shown on the display and all input is done

using the buttons.

3.11.2 Keypad

The keypad consists of 4 groups of buttons:

Start

•

The START button is used to activate the robotic

lawnmower. This is normally the last button to be

pressed before closing the hatch.

•

The 3 multi-choice buttons offer various functions,

depending on where in the menu structure you are.

The button function is shown at the bottom of the

display.

•

The number keys are used for instance to enter the

PIN code or time settings.

•

The operation selection button is symbolised by a

house. When the button has been pressed, the

selected operation mode is shown in the display.

3.11.3 Display

When the STOP button has been pressed and the hatch

is opened, the operation window appears showing the

time, selected operating mode, number of mowing

hours, battery status and timer setting.

20 - Installation

365 - 001 -

Содержание Flymo 1200R

















































Результаты поиска

Содержание Flymo 1200R

Отзывы:

Похожие инструкции для Flymo 1200R

Бренды по названию

Популярные бренды

Gardena Flymo 1200R, Руководство оператора

Результаты поиска

Содержание Flymo 1200R

Отзывы:

Похожие инструкции для Flymo 1200R

Бренды по названию

Популярные бренды