15
G
14
G
To increase the cutting performance and lengthen their working
life, the Shears should be cleaned and oiled before and after use.
Never grease the blades.
1. Clean your Edging Accu Shears with a damp cloth.
2. Oil the blades (e.g. with sewing machine oil).
The blades of your GARDENA Edging Accu Shears are non-stick
coated. To obtain good cutting results, the blades should be
cleaned thoroughly from time to time and should always be sharp.
Always remove notches and burrs caused by stones etc. imme-
diately.
1. Remove the blades (see “7. Trouble-shooting ”,
“Replacing
Grass Cutting Blades” ).
2. Separate the upper blade
8
and lower blade
9
.
3. Remove any grass and dirt between the upper and lower
blades.
4. Sharpen the blades using a sharpening stone.
5. Fit the blades (see “7. Trouble-shooting ”,
“Replacing Grass
Cutting Blades” ).
7. Trouble-shooting
Blades can cause serious injury.
V
Disconnect the Edging Accu Shears from the mains
before trouble-shooting.
Fault
Possible cause
Remedy
Edging Accu Shears
Blades are faulty.
v
Check blades and replace
do not cut well
if necessary.
Please only use original GARDENA Edging Accu Shears Trimmer
Blades:
•
Art. No. 2345 for Accu 3 / Accu 4
•
Art. No. 2346 for Accu 6
1. Loosen screws
7
and remove grass cutting blades.
2. Clean the area around the gears and lubricate the gear wheels
with non-corrosive grease (Vaseline).
3. Turn the cam gear
0
so that the marking line
A
is pointing
exactly forwards.
4. Ensure the upper blade
8
is positioned exactly in the middle
of the lower blade
9
.
5. Guide the blade underneath the blade pegs
B
of the carriage.
Make sure the cam
C
snaps into the connecting link
D
.
6. Tighten the screws
7
.
Cleaning Your Edging Accu
Shears and Oiling the Blades :
Cleaning the Blades
thoroughly and
Sharpening the Blades :
Warning !
Risk of Injury
Replacing Grass Cutting
Blades :
9 8
7 14
12
13
11
10
9
8
Warning !
Risk of Injury
Cutting Grass :
Cutting Grass with the
Telescopic Swivel Handle :
When the cutting power drops, recharge your shears immedi-
ately to prevent the cells from becoming completely empty.
There is a risk of injury if the switching devices installed
on the Shears are removed or bridged (e.g. by fastening
the on switch to the handle). This prevents the Edging Accu
Shears switching off automatically.
V
Never remove or bridge the switching devices.
The starting lockout prevents your GARDENA Edging Accu Shears
from being switched on unintentionally.
1. Clear the area to be cut of stones and other solid objects.
2. Push the starting lockout
4
forwards.
3. Press the starting switch
5
.
4. Slide the Edging Accu Shears along the lawn on their sliding
sled or wheels
6
.
This ensures a constant even cutting height.
The length of the GARDENA Telescopic Swivel Handle (Art. No.
2525) can be infinitely varied and therefore adjusted to your indi-
vidual height. The swivel handle or the Edging Accu Shears can
be swivelled up to 45°.
1. Clear the area to be cut of stones and other solid objects.
2. Attach the Telescopic Swivel Handle (see “3. Assembly”).
3. Loosen the adjusting bolt
J
.
4. Set the handle to the correct length and tighten the adjusting
bolt
J
.
5. Press and hold down the starting lockout
G
and press the
starting switch
H
.
The blades begin to cut.
6. Release the starting lockout
G
.
7. Slide the Edging Accu Shears along the grass on their sliding
sled or wheels
6
.
This ensures a constant even cutting height.
6. Maintenance
Blades can cause injury.
V
Disconnect your Edging Accu Shears from the mains
before carrying out maintenance work.
There is a risk of personal injury and damage to the Shears
if you clean them under running water (especially under
high pressure).
V
Never clean your Shears under running water.
4
5
6
4
5
17
18
20
Warning !
Risk of Injury
Warning !
Personal Injury
and Damage
to Property
