Maintenance and Cleaning
The product does not require maintenance. The product contains no parts that require servi-
cing. Therefore, do not open/dismantle it. Maintenance or repairs may only be performed by
quali
fi
ed personnel or a specialised repair shop.
Before cleaning, disconnect the weekday switch timer from the power supply. To do this,
pull it completely out of the mains socket (the wall socket). All settings are saved due to the
integrated NiMH battery.
Use a clean, dry, soft cloth for cleaning. Do not press too hard on the display; this can lead to
scratches and could also cause damage to the display and touchscreen!
Dust can easily be removed using a clean, soft and long-bristled brush and a vacuum cleaner.
Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions,
since these could damage the housing or even impair operation.
Disposal
Dispose of the unserviceable product according to the relevant statutory regulations!
Technical Data
Operating voltage ................. 230 V/AC, 50 Hz
Switching capacity ................ max. 3680 W
Protection class .................... I
Model: ................................... Relay; 1-pole disconnection
Child-proof lock ..................... yes, integrated in socket
Switch times per day ............ 16 on/off programs
Shortest switching duration .. 1 min
Countdown timer .................. 1 min to a max. of 99 h, 59 min, 59 s
Data storage ......................... with an internal NiMH battery (max. approx. 10 months with fully
charged battery)
Ambient temperature ............ 0 °C to +40 °C
Ambient humidity .................. 0% to 90% relative humidity, not condensing
Dimensions ........................... 70.5 x 132 x 37 mm (W x H x D, without plug)
Weight .................................. 200 g
Countdown Mode
In the countdown mode, a time of maximal 99 hours, 59 minutes, 59 seconds can be set.
Depending on the operating mode of the weekday switch timer, the device is switched off or on
after the timer has counted down.
☞
Operating mode “ON” or “AUTO ON” (mains socket/device is switched
on
): The
connected device is switched
off
after the timer has counted down
Operating mode “OFF” or “AUTO OFF” (mains socket/device is switched
off
): The
connected device is switched
on
after the timer has counted down
When the countdown mode was started, all automatic switching programs are deactivated
for the duration of the countdown! That means that the device is not switched on or of at
the times and weekdays programmed in the program group until the timer has counted
down.
Setting the timer and start of the countdown timer:
In the time mode, press the “MENU” button 2x until the symbol “CTD” appears on the bottom
right and the hours of the timer
fl
ash “0:00:00”.
Set the hours of the countdown timer with the “+1” or “-1” button (keep the respective button
pressed down for quick setting).
Press the “OK” button brie
fl
y to con
fi
rm.
The minutes of the countdown timer starts
fl
ashing; set the minutes with the “+1” or “-1”
button (keep the respective button pressed down for quick setting).
Press the “OK” button brie
fl
y to con
fi
rm.
The seconds of the countdown timer start
fl
ashing; set the seconds with the “+1” or “-1”
button (keep the respective button pressed down for quick setting).
The countdown timer is started by pressing the “OK” button brie
fl
y.
When the timer has counted down (at 0:00:00), the front socket and the device connected to
it is switched on or off.
☞
When the weekday switch timer is in “ON” or “AUTO ON” mode (socket/device is
switched on), the connected device is switched
off
when the timer has counted
down.
When the weekday switch timer is in “OFF” or “AUTO OFF” mode (socket/device
is switched off), the connected device is switched
on
when the timer has counted
down.
Early termination of the countdown timer:
If the countdown timer is to be terminated early, press the “MENU” button several times until
the timer is shown in the display.
☞
The countdown timer cannot be reset as long as the weekday switch timer
shows the time or the programmed switching times!
Press the counter-sunk “RCL” button brie
fl
y e.g. with a toothpick.
The countdown timer is then reset to “0:00:00”, the hours of the timer
fl
ash again (you can
now set a new time and restart the countdown timer as described above).
Press the “MENU” button brie
fl
y to leave the setting mode and to return to the time display.
Alternatively, do not press any button for 2 minutes.
This deactivates the countdown timer and the weekday switch timer continues with its normal
switching program.
Random function
With the random function, the set switch on/off times are delayed by 4 to 32 minutes.
☞
The random function can only be used for program times of the program groups,
but not for the countdown timer.
To turn the random function on or off, press the “-1” button brie
fl
y.
When the random function is turned on “RND“ is
fl
ashing on the bottom right in the display.
Reset
In order to reset the weekday switch timer to the factory settings and to delete all programming,
keep the countersunk “RST” button pressed for several seconds. All display segments are
shown in the display, then the weekday switch timer is ready for operation.
☞
Note:
All settings and programming are lost upon reset!
Activating the lighting of the LC display/night light function
Use the “
” button to switch the display light on or off.
The light can also be used as night light due to its large size and brightness.
