background image

Further information

WEEE statement

This equipment contains electrical or electronic components that 
must be recycled properly to comply with Directive 2002/96/EC of the 
European Union regarding the disposal of waster electrical and elec-
tronic equipment (WEEE). Contact your local supplier for procedures for 
recycling this equipment. 

Changes to control protocols

Keyboard manufacturers may update software or protocols in their keyboards 
without prior warning. This may change the way in which the camera behaves in 
relation to keyboard operation. We can accept no responsibility for such changes in 
keyboard manufacturer software and/or protocols.

Safety

Installation of this product should only be carried our by a competent and suitably 
qualified engineer. If you are in doubt, you should refer the installation to a suitably 
qualified person.

Disclaimer

The manufacturer reserves the right to change specifications and procedures in-
tegral to the operation, control and programming of this product at any time and 
without prior notice.
This manual relates to firmware versions 1.4.2 (standard) and 1.4.3 (thermal). 
V3 platforms.
 

Содержание C-AllView





















Отзывы: