Gamry Instruments PTC1 Скачать руководство пользователя страница 7

Unpacking and Checking a Cell Kit 

Unpacking and Checking a Cell Kit 

This section is primarily intended for the user who has just received a new Paint Test Cell Kit.   

Checking for Shipping Damage 

Your new kit was shipped disassembled to minimize shipping damage. All of the pieces were carefully 
packaged in anticipation of rough handling in shipment. Unfortunately, no matter how carefully glass pieces are 
packaged, damage sometimes occurs.   

When you first receive your kit, please check it for any signs of shipping damage. Be especially careful if the 
shipping container shows signs of rough handling.   

Obviously, the glass piece is the most susceptible to damage. Check the glass piece for chipping and small 
cracks as well as for major damage. 

 

If any parts were broken in shipment, please take a photograph and contact our USA facility or your local 
Gamry representative as soon as possible. In most cases, Gamry should have replacement parts in stock. Please 
retain the shipment

s packaging material for a possible claim against the shipping company. 

Parts List 

Please check the contents of your kit versus the packing list in Table 1. When shipped, all of the components 
should be labeled with their Gamry part number. If you are checking the completeness of an older kit, most of 
the components are shown in photographs throughout this manual. 

Table 1 

Parts in Paint Test Cell Kit PTC1 

Quantity  Part Number  Description 

930-00026 

Cell Body, PTC1, with O-ring 

935-00035 

Stopper, Rubber, PTC1 

935-00036 

Clamp, PTC1, Ace 7669-18 

935-00039 

PTC1 Base assembly 

935-00014 

Graphite Rod, 8 mm × 6" (half of 935-03) 

935-00049 

PortHole™ electroplating tape, 1 cm

2

 

935-00050 

PortHole™ electroplating tape, 3 cm

2

 

935-00051 

PortHole™ electroplating tape, 10 cm

2

 

 

Warning:

 Never use any glass parts that are chipped or cracked. Any damage to glass 

increases the probability of additional damage. Broken glass can have extremely sharp edges that represent 
a significant safety hazard. Injuries from broken glass can be quite severe. 

Содержание PTC1

















Отзывы: